05-22-2014 01:32 AM - edited 03-04-2019 11:01 PM
Good Day!
I'm currently connected with my DIA 4mbps connection (for Internet) and having a 8mbps connection for Data.
My Branch office is connected to our Main office via VPN.
My Task now is configure the 8mbps as a fail-over and all traffic related to Data line connection will go Through 8mbps Connection meaning
Data & Internet now is separate.
4mbps is configure in my router:
interface Tunnel1
description Tunnel to Turaif
ip address 10.10.10.10 255.255.255.252
tunnel source 212.76.93.113
tunnel destination 213.236.37.217
!
interface FastEthernet0/0
description Connected to STC-Sahara Router
mtu 1492
ip address 192.168.115.202 255.255.255.252
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
!
interface FastEthernet0/1
description LAN
ip address 212.76.93.113 255.255.255.248
ip nbar protocol-discovery
ip flow ingress
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
no snmp trap link-status
!
interface Dialer1
no ip address
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 192.168.115.201
ip route 10.10.50.0 255.255.255.0 212.76.93.118
ip route 172.16.0.0 255.255.255.0 10.10.10.9
ip route 172.16.1.0 255.255.255.0 10.10.10.9
ip route 172.16.2.0 255.255.255.0 212.76.93.118
ip route 172.16.3.0 255.255.255.0 212.76.93.118
ip route 172.16.7.0 255.255.255.0 212.76.93.118
ip route 172.16.13.0 255.255.255.0 10.10.10.9
ip route 172.16.14.0 255.255.255.0 10.10.10.9
ip http server
ip http authentication local
no ip http secure-server
!
!
ip nat inside source list 101 interface FastEthernet0/1 overload
!
access-list 101 permit ip 172.16.2.0 0.0.0.255 any
access-list 101 permit ip 172.16.3.0 0.0.0.255 any
and my 8mbps is separated to Cisco Router 2801. I've already configured the initial interface connection.
Int from ISP: 192.168.117.138
Int from Private IP: 172.16.3.5
My question is how can I configured the Fail over to my two lines and how can I separate the line from Data Traffic to Internet Traffic?
Thanks & Best regards,
Michael
05-22-2014 02:29 AM
Hi ,
8mbps connection for Data. - Is this is a Leased Line between main office & branch office ??
My Branch office is connected to our Main office via VPN. - is it connected IPSEC VPN tunnel over internet ??
Your requirement is configure Backup for your datalink ?? towards your branch office ??
Share me network diagram if any .
HTH
Sandy
05-22-2014 02:36 AM
8mbps for Data? Is this is a Leased Line between main office & branch office ?? - Yes Sir, this is Lease line point to point.
My Branch office is connected to our Main office via VPN. - is it connected IPSEC VPN tunnel over internet ?? - yes Sir.
Your requirement is configure Backup for your datalink ?? towards your branch office ?? - My requirement is to connect all data line traffic to our main office and Internet line separate.
Thank you
05-22-2014 08:27 PM
Hi,
According to your diagram , all your branch office connect to your routers via leased line , And internet traffic is passed via juniper firewall , everything looks okay .
Any data traffic designated between your branch office will be passed through your head office router , for internet traffic your head office router will forward the traffic to your firewall .
Its looks good
Where you want to separate data and internet traffic here ??
HTH
Sandy
05-25-2014 02:36 AM
Hi Sir,
That is my existing scenario,I have one Cisco router excess. I would like to know the configuration for failover which is any data Traffic from Main Office to Branch Site will go to Router A and any Internet Traffic will go to Router B.
Thank you in advance.
Regards,
Michael
06-09-2014 02:22 AM
Any HELP please....
Thanks & best regards,
Michael
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: