ISDN issue

[trinawong]

Debug on City A router:

Bearer Capability i = 0x8890

Standard = CCITT

Transer Capability = Unrestricted Digital

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0x81

Called Party Number i = 0x80, '02022133123'

Plan:Unknown, Type:Unknown

Dec 12 02:11:22.027 GMT: ISDN BR2/0 Q921: User RX <- RR sapi=0 tei=95 nr=13

Dec 12 02:11:22.219 GMT: ISDN BR2/0 Q921: User RX <- INFO sapi=0 tei=95, ns=14 nr=13

Dec 12 02:11:22.219 GMT: ISDN BR2/0 Q931: SETUP_ACK pd = 8 callref = 0xD5

Channel ID i = 0x89

Dec 12 02:11:22.219 GMT: ISDN BR2/0 Q921: User TX -> RR sapi=0 tei=95 nr=15

Dec 12 02:11:22.223 GMT: ISDN BR2/0 EVENT: process_rxstate: ces/callid 1/0x8F6F calltype 1 HOST_INFORMATION

Dec 12 02:11:24.839 GMT: ISDN BR2/0 Q921: User RX <- IDCKRQ ri=0 ai=127

Dec 12 02:11:24.839 GMT: ISDN BR2/0 Q921: User TX -> IDCKRP ri=61517 ai=95

Dec 12 02:11:25.835 GMT: ISDN BR2/0 Q921: User RX <- IDCKRQ ri=0 ai=127

Dec 12 02:11:25.839 GMT: ISDN BR2/0 Q921: User TX -> IDCKRP ri=62750 ai=95

Dec 12 02:11:27.207 GMT: ISDN BR2/0 Q921: User RX <- INFO sapi=0 tei=95, ns=15 nr=13

Dec 12 02:11:27.211 GMT: ISDN BR2/0 Q931: CALL_PROC pd = 8 callref = 0xD5

Dec 12 02:11:27.211 GMT: ISDN BR2/0 Q921: User TX -> RR sapi=0 tei=95 nr=16

Dec 12 02:11:27.215 GMT: ISDN BR2/0 EVENT: process_rxstate: ces/callid 1/0x8F6F calltype 1 HOST_PROCEEDING

Dec 12 02:11:27.691 GMT: ISDN BR2/0 Q921: User RX <- INFO sapi=0 tei=95, ns=16 nr=13

Dec 12 02:11:27.691 GMT: ISDN BR2/0 Q931: DISCONNECT pd = 8 callref = 0xD5

Cause i = 0x8483 - No route to destination <<<<<

Debug on City B router:

Dec 12 01:59:36.088 GMT: ISDN Se2/0:15 Q921: User TX -> RRp sapi=0 tei=0 nr=9

Dec 12 01:59:36.092 GMT: ISDN Se2/0:15 Q921: User RX <- RRf sapi=0 tei=0 nr=10

Dec 12 01:59:36.280 GMT: ISDN Se2/0:15 Q921: User RX <- RRp sapi=0 tei=0 nr=10

Dec 12 01:59:36.280 GMT: ISDN Se2/0:15 Q921: User TX -> RRf sapi=0 tei=0 nr=9

Dec 12 01:59:36.911 GMT: ISDN Se2/0:15 EVENT: UserIdle: callid 0x801F received ISDN_CALL (0x0)

Dec 12 01:59:36.911 GMT: ISDN Se2/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=10 nr=9

Dec 12 01:59:36.911 GMT: ISDN Se2/0:15 Q931: SETUP pd = 8 callref = 0x001E

Bearer Capability i = 0x8890

Standard = CCITT

Transer Capability = Unrestricted Digital

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA9839F

Exclusive, Channel 31

Called Party Number i = 0x81, '088232123423'

Plan:ISDN, Type:Unknown

Dec 12 01:59:36.919 GMT: ISDN Se2/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=11

Dec 12 01:59:36.995 GMT: ISDN Se2/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=9 nr=11

Dec 12 01:59:36.995 GMT: ISDN Se2/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x801E

Cause i = 0x8281 - Unallocated/unassigned number

Dec 12 01:59:36.995 GMT: ISDN Se2/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=10

Dec 12 01:59:36.995 GMT: ISDN Se2/0:15 EVENT: process_rxstate: ces/callid 1/0x801F calltype 1 CALL_REJECTION

Dec 12 01:59:36.995 GMT: ISDN Se2/0:15 EVENT: process_rxstate: ces/callid 1/0x801F calltype 1 CALL_CLEARED

both cities layer 1 and layer 2 have been verfiied okay, according the the debug error message, I believe it's ISDN service provider issue, can we confirm which city's service provider has problem?

thank you,

[rajivrajan1]

do u think config is ok in city A router ?

"Cause i = 0x8483 - No route to destination"

[ahpark78]

Can provide us both side of the configuration of the routers?

This may help to troubleshoot further better.

[trinawong]

yes, the configuration is correct at both end since it works well before.

Thanks,

[jayasri_r2000]

hi trina,

casue no 84

Send special information tone

The remote number you dialed is not reachable.

Check the number you dial. Verify if you need any prefixes to access the network. For example, you need to dial 9 for outbound calls through a PBX. Contact your telco/PBX administrator for details

City B service privder isse (might be pune?)

[rajivrajan1]

yes i do agree with that