07-09-2010 03:42 AM - edited 03-04-2019 09:00 AM
Hello
I have cisco SOHO97 (software version 12.4) and I can not connect to ADSL, I try with this configuration but it doesn't work :
ATM protocol: PPPoE
Ip Address: dynamic
VPI/VCI: 8/35
!
vpdn enable
!
vpdn-group pppoe
request-dialin
protocol pppoe
!
interface Dialer1
mtu 1492
ip address negotiated
ip nat outside
encapsulation ppp
dialer pool 1
ppp authentication pap callin
ppp pap sent-username <username> password <password>
!
interface ATM0
no ip address
no ip mroute-cache
no atm ilmi-keepalive
dsl operating-mode auto
pvc 8/35
encapsulation aal5snap
pppoe-client dial-pool-number 1
no shutdown
!
interface Ethernet0
ip address <IP> <mask>
ip nat inside
no ip mroute-cache
ip tcp adjust-mss 1452
no shutdown
!
ip nat inside source list 1 interface Dialer1 overload
!
access-list 1 permit any
!
I set my PC gateway to Ethernet0 IP
Please help me
07-09-2010 06:14 AM
can try adding a static default route: ip route 0.0.0.0 0.0.0.0 Dialer1
also, may i suggest using extended ACL and add PAT command below:
access-list 101 permit ip
ip nat inside source list 101 interface Dialer1 overload
07-14-2010 08:06 AM
Now I know what is the problem. I configure my soho97 like this:
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5snap
pppoe-client dial-pool-number 1
interface Dialer0
mtu 1492
ip address negotiated
ip nat outside
encapsulation ppp
dialer pool 1
no cdp enable
ppp authentication pap callin
ppp pap sent-username xxx password xxx
and when I enable ATM0 a get these messages:
*Mar 1 00:03:56.635: %LINK-3-UPDOWN: Interface ATM0, changed state to up
*Mar 1 00:03:57.635: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, chan
ged state to up
*Mar 1 00:03:57.947: %DIALER-6-BIND: Interface Vi1 bound to profile Di1
*Mar 1 00:03:57.975: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state t
o up
*Mar 1 00:04:00.431: %DIALER-6-UNBIND: Interface Vi1 unbound from profile Di1
*Mar 1 00:04:00.435: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state t
o down
*Mar 1 00:04:23.591: %DIALER-6-BIND: Interface Vi1 bound to profile Di1
*Mar 1 00:04:23.595: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state t
o up
*Mar 1 00:04:26.063: %DIALER-6-UNBIND: Interface Vi1 unbound from profile Di1
*Mar 1 00:04:26.067: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state t
o down
What can be problem ???
07-15-2010 01:17 AM
Milos, You can use "debug ppp negotiation" and "debug dialer events" to check whether the ISP is acknowledging your authentication.
rgds, dsu
07-15-2010 05:50 AM
Ok now I know what is the problem. I try with another username and pass ( with 7 characters ) and it works, but when I enter my username and pass (with 15 characters) it say Access Denied.
04-24-2017 04:08 AM
for me, it was the password, i got the same error message and it didn't go away until i fixed the mistyped password :)
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide