08-10-2005 11:53 PM - edited 03-03-2019 10:15 AM
Hi,
i have a 3640 router and was running with Nm-1E2W Network Module i have replaced it with NM-2FE2W-V2, this module is not getting detected by the router. below given is Version & Diag Information. Please advice.
IOS (tm) 3600 Software (C3640-IO3S56I-M), Version 12.1(5)T8, RELEASE SOFTWARE (
fc1)
TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Mon 07-May-01 19:58 by ccai
Image text-base: 0x60008950, data-base: 0x612EC000
ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (f
c1)
ROM: 3600 Software (C3640-IO3S56I-M), Version 12.1(5)T8, RELEASE SOFTWARE (fc1)
Router uptime is 6 minutes
System returned to ROM by power-on
System image file is "flash:c3640-io3s56i-mz_121-5_T8.bin"
cisco 3640 (R4700) processor (revision 0x00) with 45056K/4096K bytes of memory.
Processor board ID 26758246
R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
8 Low-speed serial(sync/async) network interface(s)
8 Voice FXS interface(s)
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Abbar-Jed# sh diag
Slot 0:
Unknown (type 919) Port adapter
Port adapter is disabled
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
Top Assy. Part Number : 800-21601-02
Board Revision : D0
Deviation Number : 0-8610
Fab Version : 01
PCB Serial Number : FOC09200SJG
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 97 41 01 00 C0 46 03 20 00 54 61 02
0x10: 42 44 30 80 00 00 21 A2 02 01 C1 8B 46 4F 43 30
0x20: 39 32 30 30 53 4A 47 03 00 81 00 00 00 00 04 00
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
08-11-2005 12:33 AM
Hello,
the link posted by Sankar yesterday is actually very useful:
For the NM-1FE2W-V2 and NM-2FE2W-V2 the minimum level IOS is 12.2(12)M and 12.2(13)T.
Since you are running 12.1(5)T8, you might want to try and upgrade the IOS...
HTH,
GP
04-30-2018 02:18 PM
Hello,
Thanks for the reply.
Do you know where I could find the IOS for a 2600 series? Iv'e checked the downloads page and can't find the IOS for my router (2620)
Any help would be great,
Thanks
-B
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide