06-01-2006 06:56 PM - edited 03-03-2019 12:52 PM
I have a 2811 router. I am trying to get the NME to connect through the router. I have tried just about everything. I can access the switch and the router but I can't get the network that is connected to the switch to go out the router interfaces. I have configured vlan interfaces and sub interfaces on the router.
06-01-2006 08:07 PM
Can you post your running configuration here? Maybe show where the host are connected, their ip address, and their gateway, what network and where these hosts connected to the NME is trying to get to? The NME is a switch module and needs to be configured as if it's an external switch.
Maybe this link will be of some help:
http://www.cisco.com/en/US/products/hw/modules/ps2797/products_feature_guide09186a0080415bae.html
Please rate helpful posts.
06-02-2006 07:18 AM
I can post the configuration that I have on there now but it would be one of many. I don't have a set config yet. Right now I am doing a prof of concept.
hostname
!
boot-start-marker
boot system flash:c2800nm-advipservicesk9-mz.124-7.bin
boot-end-marker
!
!
no aaa new-model
!
resource policy
!
!
!
ip cef
!
interface FastEthernet0/0
ip address 192.168.0.1 255.255.255.252
duplex auto
speed auto
!
interface FastEthernet0/1
ip address 192.168.1.2 255.255.255.252
duplex auto
speed auto
!
interface GigabitEthernet1/0
ip address 172.1.1.1 255.255.255.0
(I had to assign an address to the G1/0 so I could access the switch portion)
!
interface GigabitEthernet1/0.200
encapsulation dot1Q 200
ip address 10.10.10.1 255.255.255.0
no snmp trap link-status
!
router ospf 1
log-adjacency-changes
network 192.168.0.1 0.0.0.0 area 0.0.0.0
network 192.168.1.2 0.0.0.0 area 0.0.0.0
network 10.10.10.1 0.0.0.0 area 0.0.0.0
!
!
ip http server
no ip http secure-server
!
!
!
!
!
control-plane
!
!
!
voice-port 0/0/0
!
Here is the switch config
! Last configuration change at 17:57:37 UTC Wed May 31 2006
! NVRAM config last updated at 18:00:57 UTC Wed May 31 2006
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Switch
!
!
no aaa new-model
switch 1 provision NME-16ES-1G-P
ip subnet-zero
!
!
!
!
!
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
interface FastEthernet1/0/1
switchport access vlan 200
!
interface FastEthernet1/0/2
!
interface FastEthernet1/0/3
!
interface FastEthernet1/0/4
!
interface FastEthernet1/0/5
!
interface FastEthernet1/0/6
interface Vlan1
no ip address
shutdown
!
interface Vlan200
no ip address
!
ip classless
ip http server
ip http secure-server
!
!
control-plane
--More--
ip classless
ip http server
ip http secure-server
!
!
control-plane
!
!
line con 0
line vty 5 15
!
!
end
Switch#
Switch#
If there is a config that I could follow. I can modify as I need. I just wanted to get the data/voice to go through the router. Thanks for the help.
06-02-2006 10:49 AM
It works!!! The switch card has two virtual gig interfaces g1/0 and g1/0/2. I had to put a ip address on the g1/0 in order to access the switch module. I created a vlan with an ip address that was in the same subnet that the ip address of g1/0 was in. I then placed the g1/0/2 and all other switch ports in this vlan. I know "duu" everyone can't be router gods!! I am sure there are cleaner ways to do this without using two ip address. Thanks to Tim.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide