Hi guys!
I hope someone can help me on this.
First some information about what hardware i got.
I got a Cisco Router 860VAE, i got no console cable(so i'm connected to telnet), i got a home router too(Got it from my ISP).
I'm using my router i got from my ISP to the television so i can't just remove it.. anoying..
I was getting the Cisco router because i'm studying Cisco CCNA at my school(first year) and i thought it could be cool to make NetFlow
The router i got from my ISP is not advanced at all so not many options here. Anyway it use the IP range 10.0.0.0/8
Then my CISCO router use the ip range 192.168.1.0/24
The problem is that i can't get connection to the internet from my computer(I know...)
Let me show my running-config(remember I'm NEW):
Current configuration : 2500 bytes
!
! Last configuration change at 18:04:48 UTC Wed Jan 15 2014 by admin
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no logging buffered
enable secret 4 tnhtc92DsfdXBhelxjLWJy3243i4ntXrpb4RdfFmfqY
!
no aaa new-model
wan mode ethernet
!
!
!
ip dhcp pool ccp_pool
import all
network 192.168.1.0 255.255.255.0
dns-server 8.8.8.8 8.8.4.4
!
!
!
!
ip flow-cache timeout active 1
ip name-server 8.8.8.8
ip name-server 8.8.4.4
ip cef
no ipv6 cef
!
!
!
!
!
username admin privilege 15 secret 4 lUgFIkgcrt4SYXMq7jZtxq52lwdfgkj238
!
!
controller VDSL 0
shutdown
!
!
!
!
!
interface Loopback0
ip address 11.0.0.1 255.255.255.0
ip flow ingress
ip flow egress
!
interface Loopback1
no ip address
!
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
!
interface Ethernet0
no ip address
ip flow ingress
ip flow egress
shutdown
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
no ip address
!
interface FastEthernet3
switchport access vlan 2
no ip address
spanning-tree portfast
!
interface GigabitEthernet0
description $ETH-WAN$
ip address 10.0.0.1 255.0.0.0
ip flow ingress
ip flow egress
duplex auto
speed auto
!
interface Vlan1
ip address 192.168.1.1 255.255.255.0
ip flow ingress
ip flow egress
!
interface Vlan2
no ip address
ip flow ingress
ip flow egress
!
interface Dialer0
no ip address
ip flow ingress
ip flow egress
!
router rip
version 2
network 10.0.0.0
network 192.168.1.0
no auto-summary
!
ip default-gateway 10.0.0.100
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
ip flow-capture vlan-id
ip flow-export source Vlan1
ip flow-export version 9
ip flow-export destination 192.168.1.3 9991
!
ip route 0.0.0.0 0.0.0.0 10.0.0.100
ip route 10.0.0.0 255.0.0.0 GigabitEthernet0
ip route 192.168.1.0 255.255.255.0 Vlan1
!
mac-address-table aging-time 15
!
snmp-server community public RW
snmp-server community publics RO
snmp-server ifindex persist
snmp-server enable traps config
snmp-server host 10.0.0.3 version 2c public
!
control-plane
!
banner login ^C** CISCO **^C
!
line con 0
no modem enable
line aux 0
line vty 0 4
exec-timeout 60 0
password cisco
logging synchronous
login local
transport input telnet
!
scheduler allocate 60000 1000
!
end
I've not CHANGED anything!
Some of it was just guesswork..
When i try to PING googles DNS(IP: 8.8.8.8) from the router i get
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 36/39/40 ms
When i try to PING googles DNS from my own computer i get
Request timed out.
Request timed out.
Request timed out.
My CISCO router ip: 192.168.1.1(vlan1) 10.0.0.1(gigabitethernet/WAN)
My ISP router ip: 10.0.0.100
My computer ip: 192.168.1.3 Gateway: 192.168.1.1
Trying to make a Topology of text MY ISP -> ISP Router -> Switch -> CISCO Router -> My Computer
It's not like i can configure RIP on my ISP router so..? And BTW, my cisco router only support RIP as a routing protocol
So what do i do?
