cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5566
Views
0
Helpful
5
Replies

QOS for rdp traffic

sadoffrudoy1
Level 1
Level 1

Here is what I would like to do.....

We have an MPLS that connects our main office with our 7 branch offices.  We have 3Mb coming into the main office and 1.5 into all of the branch offices.  I would like to give rdp traffic the highest priority.  We have a Cisco 1841 at all branches and a Cisco 2811 at the main office. Do I have to configure QOS on all routers or just the one at the main location?  Any suggestions on the best way to configure this?

Thanks,

Mike

1 Accepted Solution

Accepted Solutions

Joseph W. Doherty
Hall of Fame
Hall of Fame

Disclaimer

The  Author of this posting offers the information contained within this  posting without consideration and with the reader's understanding that  there's no implied or expressed suitability or fitness for any purpose.  Information provided is for informational purposes only and should not  be construed as rendering professional advice of any kind. Usage of this  posting's information is solely at reader's own risk.

Liability Disclaimer

In  no event shall Author be liable for any damages whatsoever (including,  without limitation, damages for loss of use, data or profit) arising out  of the use or inability to use the posting's information even if Author  has been advised of the possibility of such damage.

Posting

You probably should have an egress policy on all your sites, something like:

policy-map sample

class rdp

priority percent #

class class-default

fair-queue

You'll also want to find out from you MPLS vendor what QoS support they provide (sometimes an extra cost option), and then take advantage of it.

View solution in original post

5 Replies 5

Alex Pfeil
Level 7
Level 7

I would think that you could just give port 3389 traffic the same dscp marking as voice traffic. I would set it up I GNS3 and test it first.

Yes, setup qos at all sites

Sent from Cisco Technical Support iPhone App

Joseph W. Doherty
Hall of Fame
Hall of Fame

Disclaimer

The  Author of this posting offers the information contained within this  posting without consideration and with the reader's understanding that  there's no implied or expressed suitability or fitness for any purpose.  Information provided is for informational purposes only and should not  be construed as rendering professional advice of any kind. Usage of this  posting's information is solely at reader's own risk.

Liability Disclaimer

In  no event shall Author be liable for any damages whatsoever (including,  without limitation, damages for loss of use, data or profit) arising out  of the use or inability to use the posting's information even if Author  has been advised of the possibility of such damage.

Posting

You probably should have an egress policy on all your sites, something like:

policy-map sample

class rdp

priority percent #

class class-default

fair-queue

You'll also want to find out from you MPLS vendor what QoS support they provide (sometimes an extra cost option), and then take advantage of it.

Thanks for all the replies.  Do I put this egress policy on the serial interface of all the routers?  Is it exactly the same on all the routers?

Thanks again.

Disclaimer

The   Author of this posting offers the information contained within this   posting without consideration and with the reader's understanding that   there's no implied or expressed suitability or fitness for any purpose.   Information provided is for informational purposes only and should not   be construed as rendering professional advice of any kind. Usage of  this  posting's information is solely at reader's own risk.

Liability Disclaimer

In   no event shall Author be liable for any damages whatsoever (including,   without limitation, damages for loss of use, data or profit) arising  out  of the use or inability to use the posting's information even if  Author  has been advised of the possibility of such damage.

Posting

Yes, policy would be applied to outbound egress interface, i.e. probably your serial interfaces.

A policy like the the "sample" might be applied to all routers, unless you need different percentage or want to deal with some special traffic that's unique per site.

Great, thanks.

Review Cisco Networking for a $25 gift card