04-09-2015 09:55 AM - edited 03-05-2019 01:12 AM
we have a network with several remote sites the multicast is being configured and there is only one RP currently in the whole network for all sites.
the quality of service was being configured too but the issue is when ever i tried to stream a multicast video, the remote sites get very bad quality its choppy pixlated and sometimes no video the WAN shaping policy say's AF41 if i am not wrong.
can anyone help me out in configuring the standard policy for audio video and multicast network streams for the network so that i can configure it standard for the network
04-09-2015 10:18 AM
Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
What kind of video, streaming or live (e.g. video conferencing)?
A QoS policy for either, should try to preclude drops.
A QoS policy of for the latter should also try to preclude jitter and delay.
DSCP, itself, is just a tag to quickly identify the service needs of the corresponding traffic. I.e. there's nothing special about any DSCP marking, such as AF41; there's both RFC and Cisco (very similar) marking recommendations.
There are often recommendations/examples (Cisco offers many [which have also changed over time]) how to treat different traffic classes, but lean toward such more as examples. Try to understand why a certain recommendation is being made how to treat certain traffic rather than taking it a cookbook recipe.
04-09-2015 12:21 PM
thank you for your response Joseph actually we have different types of data traffic from central point to all other remote campuses like imaging, replication of Data center data and voice and video conferencing.
imaging usually use multicast and it is configure properly, i am using a server which is multicast the live or recorded video over the network and my remote campus access it though VLC now i can see the pipe is free but they are having choppy video and low quality of video. especially when its live
i tried using Uni-cast and it works like a charm no issues at all even with so many streams
what i am really trying to achive is to mark or specify the traffic on switches and routers or wan routers and then put a standard quality of service so that atleast that traffic can be given priority for sure.
04-10-2015 02:20 AM
Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Assuming your unicast and multicast video are using similar CODECs, and similar bandwidths, then both should behave about the same. If, as you believe, the unicast traffic has a particular tag and the multicast doesn't, then your equipment could treat the unicast and multicast differently. Generally, Cisco's equipment doesn't treat differently tagged traffic differently until configured to do so. Many Cisco switches, when QoS is enabled on them, do treat some tags differently by default. Cisco routers normally require a manual configuration beyond just enabling QoS.
So far, from what you've described, implies there may be some QoS configuration support for unicast but not multicast.
04-23-2015 08:12 AM
apology for late reply.....
so can you help me creating one standard qos policy as required below
04-23-2015 09:52 AM
Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Can I help you? Perhaps, depends on how much help you need (and how much spare time I have). (Others will help too. Hint, the more focused the question, the better your chances of getting assistance.)
Post your logical policy, detailed information about your network, and what QOS you propose doing on your devices.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide