There are some troubles in my 7206 vxr . The process of this problem below.
LOG:
Self decompressing the image : ########################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################## [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, 7200 Software (C7200P-ADVIPSERVICESK9-M), Version 12.4(22)T, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 10-Oct-08 11:19 by prod_rel_team
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Installed image archive
Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory.
Processor board ID 37106353
MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2
6 slot VXR midplane, Version 2.11
Last reset from power-on
PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb1 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
Please refer to the following document "Cisco 7200 Series Port Adaptor
Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>
for c7200 bandwidth points oversubscription and usage guidelines.
1 FastEthernet interface
3 Gigabit Ethernet interfaces
2045K bytes of NVRAM.
253008K bytes of ATA PCMCIA card at slot 2 (Sector size 512 bytes).
65536K bytes of Flash internal SIMM (Sector size 512K).
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: n
Press RETURN to get started!
*Jan 1 00:00:06.539: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
*Jan 1 00:00:06.539: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to up
*Jan 1 00:00:06.539: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
*Jan 1 00:00:06.539: %LINK-3-UPDOWN: Interface GigabitEthernet0/3, changed state to down
*Jan 1 00:00:06.539: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to down
*Jan 1 00:00:07.219: %LINEPROTO-5-UPDOWN: Line protocol on Interface SSLVPN-VIF0, changed state to up
*Jan 1 00:00:07.539: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
*Jan 1 00:00:07.539: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/2, changed state to down
*Jan 1 00:00:07.539: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/3, changed state to down
*Jan 1 00:00:07.539: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
*Jan 1 00:00:57.367: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to administratively down
*Jan 1 00:00:57.391: %LINK-5-CHANGED: Interface FastEthernet0/2, changed state to administratively down
*Jan 1 00:00:57.407: %LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to administratively down
*Jan 1 00:00:57.435: %LINK-5-CHANGED: Interface GigabitEthernet0/3, changed state to administratively down
*Jan 1 00:00:58.367: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down
*Jan 1 00:01:04.003: %SYS-5-RESTART: System restarted --
Cisco IOS Software, 7200 Software (C7200P-ADVIPSERVICESK9-M), Version 12.4(22)T, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 10-Oct-08 11:19 by prod_rel_team
*Jan 1 00:01:04.007: %ENTITY_ALARM-6-INFO: ASSERT CRITICAL SFP Slot 0/1 SFP is missing
*Jan 1 00:01:04.007: %ENTITY_ALARM-6-INFO: ASSERT INFO Gi0/1 Physical Port Administ
*Jan 1 00:01:04.007: %ENTITY_ALARM-6-INFO: ASSERT CRITICAL SFP Slot 0/2 SFP is missing
*Jan 1 00:01:04.007: %ENTITY_ALARM-6-INFO: ASSERT INFO Gi0/2 Physical Port Administrative State Down
*Jan 1 00:01:04.007: %ENTITY_ALARM-6-INFO: ASSERT CRITICAL SFP Slot 0/3 SFP is missing
*Jan 1 00:01:04.007: %ENTITY_ALARM-6-INFO: ASSERT INFO Gi0/3 Physical Port Administrative State Down
*Jan 1 00:01:04.007: %ENTITY_ALARM-6-INFO: ASSERT INFO Fa0/2 Physical Port Administrative State Down
*Jan 1 00:01:04.783: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Jan 1 00:01:04.783: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
*Jan 1 00:01:04.835: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
Router>
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hos
Router(config)#hostname r1
r1(config)#end
r1#wr
NV: Invalid Magic(0x824A) found in NVRAM.....Erase of configuration files recommended
startup-config file open failed (Not enough space)
r1#
*Jan 1 00:01:20.599: %SYS-5-CONFIG_I: Configured from console by console
r1#
r1#
r1#
r1#sh star
r1#sh startup-config
startup-config is not present
r1#dir nvram:
Directory of nvram:/
2044 -rw- 0 <no date> startup-config
2045 ---- 0 <no date> private-config
2046 -rw- 0 <no date> underlying-config
1 ---- 49 <no date> persistent-data
2095096 bytes total (2094020 bytes free)
I nend some help.
