Hi all,
I have replaced the standby module of 7600 series due to a sup hang-up.Now the added new SUP is stuck in STANDBY COLD.before it was in sso mode and changed in to rpr mode .Also in the bootsync there is two IOS(SRB5 and SRB2) and before i was not copied the SRB2 to the new SUP.I had added it now only .After that i havent reload the card.does that the absence of SRB2 in the sup5 is the problem.please assist
Many thanks in advance!!!
CHN-7606-EDGE1#sh red
Redundant System Information :
------------------------------
Available system uptime = 7 weeks, 1 day, 13 hours, 47 minutes
Switchovers system experienced = 0
Standby failures = 14
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = rpr
Maintenance Mode = Disabled
Communications = Up
Current Processor Information :
-------------------------------
Active Location = slot 6
Current Software state = ACTIVE
Uptime in current state = 7 weeks, 1 day, 13 hours, 46 minutes
Image Version = Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVIPSERVICES-M), Versio
n 12.2(33)SRB5, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Wed 05-Nov-08 17:23 by prod_rel_team
BOOT = sup-bootdisk:c7600s3223-advipservices-mz.122-33.SRB5.bin,1;sup-bootdisk:c7600s3223
-advipservicesk9-mz.122-33.SRB2.bin,1;
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Peer Processor Information :
----------------------------
Standby Location = slot 5
Current Software state = STANDBY COLD
Uptime in current state = 20 hours, 40 minutes
Image Version = Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVIPSERVICES-M), Versio
n 12.2(33)SRB5, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Wed 05-Nov-08 17:23 by prod_rel_team
BOOT = sup-bootdisk:c7600s3223-advipservices-mz.122-33.SRB5.bin,1;sup-bootdisk:c7600s3223
-advipservicesk9-mz.122-33.SRB2.bin,1;
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
CHN-7606-EDGE1#dir slavesup-bootdisk:
Directory of slavesup-bootdisk:/
1 -rw- 47628228 Mar 30 2009 11:18:18 +05:30 s3223-ipbase_wan-mz.122-18.SXF15a.bin
2 -rw- 71767492 Aug 1 2009 02:29:02 +05:30 c7600s3223-advipservices-mz.122-33.SRB5.bin
3 -rw- 26286080 Aug 1 2009 02:41:26 +05:30 c7600-fpd-pkg.122-33.SRB5a.pkg
4 -rw- 231041 Aug 2 2009 16:47:26 +05:30 crashinfo_20090802-111726
5 -rw- 28819456 Aug 3 2009 11:59:38 +05:30 c7600s3223-advipservicesk9-mz.122-33.SRB2.bin
CHN-7606-EDGE1#sh sup-bootdisk:
-#- --length-- -----date/time------ path
1 26287104 Nov 10 2007 00:09:12 c7600-fpd-pkg.122-33.SRB2.pkg
2 26843548 Nov 08 2007 15:12:28 sea_log.dat
4 71767492 Aug 02 2009 11:50:18 c7600s3223-advipservices-mz.122-33.SRB5.bin
5 26286080 Aug 02 2009 11:52:28 c7600-fpd-pkg.122-33.SRB5a.pkg
6 26191872 Nov 08 2007 16:16:10 c7600-fpd-pkg.122-33.SRB1.pkg
7 73508356 Nov 09 2007 23:13:42 c7600s3223-advipservicesk9-mz.122-33.SRB2.bin