cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1049
Views
0
Helpful
1
Replies

Unexpected reboot 4948E

valintinr
Level 1
Level 1

Hello,
We have before Cisco 65 with 720 Sup but we have to replace it with 4948E. Configured (copied from prewious one) BGP with multiple peers and traffic shaping (copied too) per ip via policy-map.

Now when I try to change shape shaper 4948E suddenly rebooted. I've tried this few time and rebboted every time.

Some tech info.

Log Buffer (4096 bytes):

*Jul 26 10:29:22.199: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
*Jul 26 10:29:24.139: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 1 (WS-C4948E S/N: CAT1601S3YS Hw: 2.0) is online
*Jul 26 13:29:24: %SYS-6-CLOCKUPDATE: System clock has been updated from 10:29:24 UTC Tue Jul 26 2016 to 13:29:24 EET Tue Jul 26 2016, configured from console by console.
*Jul 26 13:29:26: %SYS-5-CONFIG_I: Configured from memory by console
*Jul 26 13:29:26: %SYS-5-RESTART: System restarted --
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-ENTSERVICESK9-M), Version 15.2(1)E, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 27-Aug-13 12:44 by prod_rel_team
*Jul 26 13:29:26: %SSH-5-ENABLED: SSH 1.99 has been enabled
*Jul 26 13:29:26: %SNMP-5-COLDSTART: SNMP agent on host SW35-UA is undergoing a cold start
*Jul 26 13:29:31: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=1 Port=49: Transceiver has been inserted
*Jul 26 13:29:34: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=1 Port=50: Transceiver has been inserted
*Jul 26 13:29:37: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=1 Port=51: Transceiver has been inserted
*Jul 26 13:29:38: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=1 Port=52: Transceiver has been inserted
*Jul 26 13:30:06: %BGP-5-ADJCHANGE: neighbor 31.28.16.1 Up
*Jul 26 13:30:13: %BGP-5-NBR_RESET: Neighbor 194.44.6.233 active reset (BGP Notification sent)
*Jul 26 13:30:13: %BGP-5-ADJCHANGE: neighbor 194.44.6.233 Up
*Jul 26 13:30:16: %BGP-5-ADJCHANGE: neighbor 195.211.108.126 Up
*Jul 26 13:30:18: %BGP-5-ADJCHANGE: neighbor 195.35.65.11 Up
*Jul 26 13:30:22: %BGP-5-ADJCHANGE: neighbor 195.211.108.122 Up

SW35-UA#show version
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-ENTSERVICESK9-M), Version 15.2(1)E, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 27-Aug-13 12:44 by prod_rel_team

ROM: 12.2(44r)SG11
SW35-UA uptime is 4 minutes
System returned to ROM by abort at PC 0x0
System restarted at 13:28:47 EET Tue Jul 26 2016
System image file is "bootflash:cat4500e-entservicesk9-mz.152-1.E.bin"
Hobgoblin Revision 21, Fortooine Revision 1.40

Last reload reason: abort at PC 0x0

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco WS-C4948E (MPC8548) processor (revision 5) with 1048576K bytes of memory.
Processor board ID CAT1601S3YS
MPC8548 CPU at 1GHz, Cisco Catalyst 4948E
Last reset from System Crash
10 Virtual Ethernet interfaces
48 Gigabit Ethernet interfaces
4 Ten Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.

Configuration register is 0x2101

vlan configuration 233,237
service-policy output World-out-pmap

interface TenGigabitEthernet1/51
switchport access vlan 233
switchport mode access
no cdp enable
spanning-tree bpdufilter enable
spanning-tree bpduguard disable
spanning-tree guard none
service-policy input World-in-pmap

ip access-list standard Positive-Plus-out-acl
permit 195.xxx

ip access-list extended Positive-Plus-in-acl
permit ip any host 195.xxx

class-map match-all Positive-Plus-in-cmap
match access-group name Positive-Plus-in-acl

class-map match-all Positive-Plus-out-cmap
match access-group name Positive-Plus-out-acl

policy-map World-out-pmap

class Positive-Plus-out-cmap
police cir 20000000 bc 75000 be 75000 conform-action transmit exceed-action drop violate-action drop

policy-map World-in-pmap

class Positive-Plus-in-cmap
police cir 20000000 bc 75000 be 75000 conform-action transmit exceed-action drop violate-action drop

So I've typed next command

SW35-UA(config)#policy-map World-out-pmap
SW35-UA(config-pmap)# class Positive-Plus-out-cmap
SW35-UA(config-pmap-c)#no police cir 20000000 bc 75000 be 75000 conform-action transmit exceed-action drop violate-action drop
SW35-UA(config-pmap-c)#police cir 20000000 bc 75000 be 75000 conform-action transmit exceed-action drop violate-actissh: Write failed: Broken pipe

As you see after no police I have few second before reboot (I've used UP arrow to replace 20M within 50M). That's all

1 Reply 1

valintinr
Level 1
Level 1

Fixed after upgrading to   Version 15.1(2)SG7

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: