cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Choose one of the topics below for SD-WAN Resources to help you on your journey with SD-WAN

This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC!
We will not comment or assist with your TAC case in these forums.

525
Views
0
Helpful
0
Replies
DaeHeon Kang
Beginner

SDWAN BGP configuration on transport side(ISR base)

I am looking for the CLI or template configuration example about BGP configuration on transport side.

I've tried to configure with the relevant Cisco document, 

however it returns error message when I tried to push template to Edge devices(ISR router).

The below is the configuration that I've done and error message.

 

>>> Configuration example

 viptela-system:system
   device-model          vedge-ISR-4331
   host-name             Test-Router
   system-ip             200.200.200.2
   overlay-id            1
   site-id               100
   port-offset           0
   control-session-pps   300
   admin-tech-on-failure
   sp-organization-name  "SD-WAN-1 - xxxxx"
   organization-name     "SD-WAN-1 - xxxxx"
   port-hop
   track-transport
   track-default-gateway
   console-baud-rate     9600
   vbond 203.42.41.250 port 12346
   logging
    disk
     enable
    !
   !
  !
  bfd app-route multiplier 6
  bfd app-route poll-interval 600000
  omp
   no shutdown
   graceful-restart
  !
  security
   ipsec
    rekey               86400
    replay-window       512
    authentication-type sha1-hmac ah-sha1-hmac
   !
  !
  no service pad
  no service tcp-small-servers
  no service udp-small-servers
  hostname Test-Router
  username admin privilege 15 secret 9 $9$3VEF3VAI3lMM3E$awMmxogwHvRdxoHA5u1utUOAmKPBUvUbkD4PnwNWmWk
  vrf definition Mgmt-intf
   description Transport VPN
   rd          1:512
   address-family ipv4
    exit-address-family
   !
   address-family ipv6
    exit-address-family
   !
  !
  no ip finger
  no ip rcmd rcp-enable
  no ip rcmd rsh-enable
  no ip dhcp use class
  ip prefix-list Test-Loopback permit 10.10.10.10/32
  no ip igmp ssm-map query dns
  interface GigabitEthernet0
   no shutdown
   arp timeout 1200
   vrf forwarding Mgmt-intf
   no ip address
   ip redirects
   ip mtu    1500
   mtu 1500
   negotiation auto
  exit
  interface GigabitEthernet0/0/0
   no shutdown
   arp timeout 1200
   ip address 100.200.200.2 255.255.255.252
   ip redirects
   ip mtu    1500
   mtu 1500
   negotiation auto
  exit
  interface Loopback0
   no shutdown
   arp timeout 1200
   ip address 10.10.10.10 255.255.255.255
   ip mtu 1500
  exit
  interface Tunnel0
   no shutdown
   ip unnumbered Loopback0
   no ip redirects
   ipv6 unnumbered Loopback0
   no ipv6 redirects
   tunnel source Loopback0
   tunnel mode sdwan
  exit
  route-map Route-Polocy permit 1
   match ip address prefix-list Test-Loopback
  !
  clock timezone UTC 0 0
  logging persistent size 104857600 filesize 10485760
  logging buffered 512000
  no logging rate-limit
  logging persistent
  aaa authentication login default local
  aaa authorization exec default local
  aaa session-id common
  no crypto ikev2 diagnose error
  router bgp 65332
   bgp router-id        10.10.10.10
   bgp log-neighbor-changes
   distance bgp 20 200 20
   neighbor 100.200.200.1 remote-as 65330
   neighbor 100.200.200.1 ebgp-multihop 1
   address-family ipv4 unicast
    redistribute connected route-map Route-Polocy
    exit-address-family
   !
   timers bgp 60 180
  !
  line con 0
   login authentication default
   speed    9600
   stopbits 1
  !
  sdwan
   interface GigabitEthernet0/0/0
   exit
   interface Loopback0
    tunnel-interface
     encapsulation ipsec weight 1
     no border
     color gold
     no last-resort-circuit
     no low-bandwidth-link
     control-connections
     no vbond-as-stun-server
     vmanage-connection-preference 5
     port-hop
     carrier                       default
     nat-refresh-interval          5
     hello-interval                1000
     hello-tolerance               12
     no allow-service all
     no allow-service bgp
     allow-service dhcp
     allow-service dns
     allow-service icmp
     no allow-service sshd
     no allow-service netconf
     no allow-service ntp
     no allow-service ospf
     no allow-service stun
     no allow-service snmp
    exit
   exit
   omp
    no shutdown
    send-path-limit  4
    ecmp-limit       4
    graceful-restart
    timers
     holdtime               60
     advertisement-interval 1
     graceful-restart-timer 43200
     eor-timer              300
    exit
    address-family ipv4
     advertise connected
     advertise static
    !
    address-family ipv6
     advertise connected
     advertise static
    !
   !
  !
  policy
   no app-visibility
   no flow-visibility
   no implicit-acl-logging
   log-frequency        1000

 

>>>>>>> Error message

8-Sep-2019 9:20:55 UTC] Configuring device with feature template: Test-Router-template
[8-Sep-2019 9:20:55 UTC] Generating configuration from template
[8-Sep-2019 9:21:00 UTC] Checking and creating device in vManage
[8-Sep-2019 9:21:01 UTC] Device is online
[8-Sep-2019 9:21:01 UTC] Updating device configuration in vManage
[8-Sep-2019 9:21:07 UTC] Pushing configuration to device
[8-Sep-2019 9:21:20 UTC] Failed to process device request. Error response : rpc-reply error: <rpc-reply xmlns="urn:ietf:params:xml:ns:netconf:base:1.0" xmlns:nc="urn:ietf:params:xml:ns:netconf:base:1.0" message-id="13">
  <rpc-error>
    <error-type>application</error-type>
    <error-tag>operation-failed</error-tag>
    <error-severity>error</error-severity>
    <error-app-tag>too-few-elements</error-app-tag>
    <error-path xmlns:viptela-vpn="http://viptela.com/vpn">
    /viptela-vpn:vpn/viptela-vpn:vpn-instance[viptela-vpn:vpn-id='0']/viptela-vpn:interface[viptela-vpn:if-name='GigabitEthernet0/0/0']/viptela-vpn:tunnel-interface/viptela-vpn:encapsulation
  </error-path>
    <error-message unknown:lang="en">too few /vpn/vpn-instance[vpn-id='0']/interface[if-name='GigabitEthernet0/0/0']/tunnel-interface/encapsulation, 0 configured, at least 1 must be configured</error-message>
    <error-info xmlns:tailf="http://tail-f.com/ns/netconf/params/1.1" xmlns:viptela-vpn="http://viptela.com/vpn">
      <tailf:bad-instance-count>
        <tailf:bad-element>/viptela-vpn:vpn/viptela-vpn:vpn-instance[viptela-vpn:vpn-id='0']/viptela-vpn:interface[viptela-vpn:if-name='GigabitEthernet0/0/0']/viptela-vpn:tunnel-interface/viptela-vpn:encapsulation</tailf:bad-element>
        <tailf:instances>0</tailf:instances>
        <tailf:min-instances>1</tailf:min-instances>
      </tailf:bad-instance-count>
    </error-info>
  </rpc-error>
</rpc-reply>
0 REPLIES 0
Content for Community-Ad