Hi,when we update the MX Firmware from 19.1.12 to stable Firmware 19.2.7, we get DNS_EVENT_BAD_PACKET_LENGTH (Event ID 5501) and the oversized DNS packets (EDNS0) are thrown away.Had anyone the same issue in the past or yet and a solution for this be...
Forum Posts
We need to change our VPN hub to the cloud, so naturally being meraki full stack, I looked to using vMX. The trial form on the website does not my email address (or indeed any address). I obtained the email of my sales rep from the meraki dashboard a...
I am configuring static NAT on a Cisco 891FJ router.What is the recommended number of NAT entries? (For example, around 100 to 300.)
Hello everyone,On Cisco cEdge devices, I'm not able to see the MAC address of the directly connected remote device interface from the CLI, regardless of whether it's a Layer 2 or Layer 3 connection.Is this expected behavior in Cisco SD-WAN, or could ...
Received a brand new ISR 1100 series(PID in title). As an assignment, I'm trying to set up the internal AP for wireless connectivity in a computer lab. Connected an ethernet cable to the g0/0/1 interface its up. Also enabled the wlan0/1/4 interface.W...
Hello, everyone.Here is my topology:It's a very simple MPLS L3 VPN scenario. R3 is advertising 3.3.3.3/32 to both routers via BGP. R1-XR and R2 are configured with as-override.I've configured R2 to advertise itself with a higher local preference, whi...
Full Meraki environment: MX, MR, MS. The WAP are in a subnet that has proxy to upstream DNS configured.When that is changed in the DHCP settings to use e.g. OpenDNS or 1.1.1.3, the WAP will report "Misconfigured DNS". Why is that ?
I have a MX450 currently supporting approximately 6.5K-7K clients. The throughput according to API calls peaks around 7Gbs. IDS/IPS is switched off. Performance score never exceeds 40 when polled via an API call every 10 minutes. Free memory plateaus...
Does Cisco, or anyone else do a cable that will allow me to connect my USB only laptop to a console port on a Cisco device?Thanks
Hello Cisco Community Team,We are currently using Cisco SD-WAN (vManage) and running into confusion with Centralized Policy and Policy Group configuration.At the moment, both Centralized Policy and Policy Group are configured in our environment. Howe...
Hello, everyone.I am reading the MPLS Layer 3 VPN Configuration guide for ASR 9000 which states:https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/26xx/l3vpn/configuration/guide/b-l3vpn-cg-asr9000-26xx.pdfYou must remove IPv4/IPv6 address...
##### Turns out it was KEEPALIVES ### This should be simple but I cannot get it to work!One end of the GRE Tunnel is C9500-24Y4C. Advantage licensing.Other end is a Palo Alto FW.I'm trying to stick the switch side tunnel interface into a specific VRF...
Hi community!I am currently in the process of designing an On-prem SD-WAN solution, where Edge devices will use the internet to communicate with Validator and Controller primarily. MPLS transports may be added in the future.Anyway, I am looking at th...
Hey, guys I am having some trouble here with IP sla and track configuration in here. So first I configured two static default routes on ASA towards isp1 and isp2 with making the default route towards isp2 as floatic static route with ad 10 and applie...
Hello Guys, Currently I have a "device-template" with almost 200 devices attached to it, I need to make a change in one of it's associated "feature-templates", from what I can see I could one of two things: 1. Create a new "feature-template" and new ...
