12-08-2015 09:42 PM
Hi
I have cisco MDS 9509 ("Supervisor/Fabric-2") running version version 3.3(5b)
In order to ugrade the OS to 4.2.9 i had replaced existing IP Storage Services Module DS-X9308-SMIP has been repalced with 4x1GE IPS, 18x1/2/4Gbps FC Module DS-X9304-18K9
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ------------------ ------------
2 22 4x1GE IPS, 18x1/2/4Gbps FC Modu DS-X9304-18K9 ok
3 24 1/2/4 Gbps FC Module DS-X9124 ok
4 24 1/2/4 Gbps FC Module DS-X9124 ok
The new module had come up and all GigabitEthernet interface is also coming up , but when i had connected the same to network switch its not showing the connectivity
i had tried connecting a cross cable with laptop and GigabitEthernet port , but the port status doesnt not change , also its not able to ping the device
The hardware version fo new module is 1.8 , what could be the couse of the issue
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ------------------ ------------
2 22 4x1GE IPS, 18x1/2/4Gbps FC Modu DS-X9304-18K9 ok
3 24 1/2/4 Gbps FC Module DS-X9124 ok
4 24 1/2/4 Gbps FC Module DS-X9124 ok
5 0 Supervisor/Fabric-2 DS-X9530-SF2-K9 active *
6 0 Supervisor/Fabric-2 DS-X9530-SF2-K9 ha-standby
7 8 IP Storage Services Module DS-X9308-SMIP ok
8 12 1/2/4 Gbps FC Module DS-X9112 ok
9 24 1/2/4 Gbps FC Module DS-X9124 ok
Mod Sw Hw World-Wide-Name(s) (WWN)
--- -------------- ------ --------------------------------------------------
2 3.3(5b) 1.8 20:41:00:0d:ec:6b:e5:c0 to 20:52:00:0d:ec:6b:e5:c0
3 3.3(5b) 1.6 20:81:00:0d:ec:6b:e5:c0 to 20:98:00:0d:ec:6b:e5:c0
4 3.3(5b) 1.6 20:c1:00:0d:ec:6b:e5:c0 to 20:d8:00:0d:ec:6b:e5:c0
5 3.3(5b) 1.4 --
6 3.3(5b) 1.4 --
7 3.3(5b) 8.0 --
8 3.3(5b) 1.5 21:c1:00:0d:ec:6b:e5:c0 to 21:cc:00:0d:ec:6b:e5:c0
9 3.3(5b) 1.6 22:01:00:0d:ec:6b:e5:c0 to 22:18:00:0d:ec:6b:e5:c0
12-09-2015 08:37 AM
Hi,
Go for the upgrade.
CSCty07888 GigE interfaces stay 'initializing' with DS-X9304-18k9 and SAN-OS 3.3
Symptom:
GigE interfaces remain in the "initializing" status on linecard module part numer DS-X9304-18K9.
Conditions:
San-OS 3.x and the 18/4 MSM module DS-X9304-18K9 with HW version 1.5 (or above).
Workaround:
Upgrade to NX-OS 4.x or above or replace the DS-X9304-18K9 linecard with a HW version lower than 1.5.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide