Hello,
I have a router Cisco 886VA with following configuration:
Cisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.3(3)M6, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2015 by Cisco Systems, Inc. Compiled Tue 04-Aug-15 05:50 by prod_rel_team ROM: System Bootstrap, Version 15.4(1r)T1, RELEASE SOFTWARE (fc1) ber-gate1 uptime is 1 hour, 25 minutes System returned to ROM by reload at 14:05:35 cet Mon Dec 18 2017 System image file is "flash:c800-universalk9-mz.SPA.153-3.M6.bin" interface ATM0 no ip address no atm ilmi-keepalive ! interface ATM0.1 point-to-point pvc 1/32 pppoe-client dial-pool-number 1 ! ! interface BRI0 no ip address encapsulation hdlc shutdown isdn termination multidrop ! interface Ethernet0 no ip address shutdown ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 description LAN no ip address duplex full ! interface Vlan1 description LAN ip address 192.168.1.254 255.255.255.0 ip nat inside no ip virtual-reassembly in ! interface Dialer0
sh interfaces fastEthernet 3
FastEthernet3 is up, line protocol is up
Hardware is Fast Ethernet, address is 002a.102c.9a5b (bia 002a.102c.9a5b)
Description: LAN
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:04:07, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
413 packets input, 98793 bytes, 0 no buffer
Received 144 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
2417 packets output, 183930 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
14 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
2 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
sh vlan-switch VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0, Fa1, Fa2, Fa3
I have plugged in a computer direct to port 3, but I don't see any traffic, any activity. The computer has IP 192.168.1.253/24. What i have forgotten?
Hi Georg,
it is strange. I have pinged the computer from Cisco - it works:
ping 192.168.1.253 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.253, timeout is 2 seconds: .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms
And after that I can see the traffic:
is it common behavior?
