C3560 and One Client. Can't ping the client from the switch

[itm-network-support]

I have a stand alone C3560 with the below setup.

The client has 10.10.200.3. I am connected into port 48 and have the CLI up on the console port.

I have no gateway to connect to.

I am just trying to upgrade the IOS software to begin setting up my config. I have a tftp server bound to 10.10.200.3.

I have no firewalls on my machine.

I do not have the command "ip routing".

I have tested the client on my production network and have no issues pinging it.

What am I missing? I feel so dumb.

Current configuration : 2274 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Switch
!
boot-start-marker
boot-end-marker
!
!
!
!
no aaa new-model
system mtu routing 1500
!
!
!
!
!
spanning-tree mode pvst
spanning-tree extend system-id
!
!
!
!
vlan internal allocation policy ascending
!
!
!
interface FastEthernet0
 no ip address
!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
interface GigabitEthernet0/3
!
interface GigabitEthernet0/4
!
interface GigabitEthernet0/5
!
interface GigabitEthernet0/6
!
interface GigabitEthernet0/7
!
interface GigabitEthernet0/8
!
interface GigabitEthernet0/9
!
interface GigabitEthernet0/10
!
interface GigabitEthernet0/11
!
interface GigabitEthernet0/12
!
interface GigabitEthernet0/13
!
interface GigabitEthernet0/14
!
interface GigabitEthernet0/15
!
interface GigabitEthernet0/16
!
interface GigabitEthernet0/17
!
interface GigabitEthernet0/18
!
interface GigabitEthernet0/19
!
interface GigabitEthernet0/20
!
interface GigabitEthernet0/21
!
interface GigabitEthernet0/22
!
interface GigabitEthernet0/23
!
interface GigabitEthernet0/24
!
interface GigabitEthernet0/25
!
interface GigabitEthernet0/26
!
interface GigabitEthernet0/27
!
interface GigabitEthernet0/28
!
interface GigabitEthernet0/29
!
interface GigabitEthernet0/30
!
interface GigabitEthernet0/31
!
interface GigabitEthernet0/32
!
interface GigabitEthernet0/33
!
interface GigabitEthernet0/34
!
interface GigabitEthernet0/35
!
interface GigabitEthernet0/36
!
interface GigabitEthernet0/37
!
interface GigabitEthernet0/38
!
interface GigabitEthernet0/39
!
interface GigabitEthernet0/40
!
interface GigabitEthernet0/41
!
interface GigabitEthernet0/42
!
interface GigabitEthernet0/43
!
interface GigabitEthernet0/44
!
interface GigabitEthernet0/45
!
interface GigabitEthernet0/46
!
interface GigabitEthernet0/47
!
interface GigabitEthernet0/48
 switchport mode access
!
interface GigabitEthernet1/1
!
interface GigabitEthernet1/2
!
interface GigabitEthernet1/3
!
interface GigabitEthernet1/4
!
interface TenGigabitEthernet1/1
!
interface TenGigabitEthernet1/2
!
interface Vlan1
 ip address 10.10.200.2 255.255.255.0
!
ip http server
ip http secure-server
!
!
line con 0
line vty 5 15
!
end

[itm-network-support]

Switch#sho int vlan1
Vlan1 is up, line protocol is up
  Hardware is EtherSVI, address is 1005.caa3.dac0 (bia 1005.caa3.dac0)
  Internet address is 10.10.200.2/24
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive not supported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:50, output 00:02:31, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     536 packets input, 46624 bytes, 0 no buffer
     Received 0 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     62 packets output, 4925 bytes, 0 underruns
     0 output errors, 3 interface resets
     0 output buffer failures, 0 output buffers swapped out

[paul driver]

Hello

Can you please provide the current status on this issue....

Can you ping the pc acting a the tftp server from the switch/router?
Does this pc have tftp server active with the IOS you want install?
Is this PC allowing TFTP via it software fw or is the FW turned off?
Can you post the actual command you are using to download this IOS to the switch/router?
Can you post the error message ( if applicable) that is produced when you try to install this IOS>

Can you post - dir flash:

res

Paul