cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
Join Customer Connection to register!
6915
Views
0
Helpful
6
Replies
Hulk8647
Beginner

Cannot boot ISR 4321

I cannot boot this router for the life of me. I am stuck in rommon. The image is there:

 

rommon 1 > dir bootflash:

0   0         drw-     lost+found
0   0         drw-     .prst_sync
0   0         drw-     .installer
0   0         drw-     core
0   0         drw-     .rollback_timer
0   0         -rw-     tracelogs.548
0   0         drw-     tracelogs
0   30        -rw-     throughput_monitor_params
0   549586049 -rw-     isr4300-universalk9.16.06.02.SPA.bin

When I do

 

boot bootflash:isr4300-universalk9.16.06.02.SPA.bin

The router just boots to rommon again.

 

rommon 1 > boot usb1:isr4300-universalk9.16.06.02.SPA.bin
boot: unsupported boot device "usb1"
rommon 2 > boot bootflash:isr4300-universalk9.16.06.02.SPA.bin
File size is 0x20c20481
Located isr4300-universalk9.16.06.02.SPA.bin
Image size 549586049 inode num 15, bks cnt 134177 blk size 8*512
############################################################################################################
Boot image size = 549586049 (0x20c20481) bytes

Package header rev 1 structure detected
Calculating SHA-1 hash...done
validate_package: SHA-1 hash:
        calculated ecc5b5b6:ebc75039:f88a7236:2b567f13:e45804bf
        expected   ecc5b5b6:ebc75039:f88a7236:2b567f13:e45804bf

RSA Signed RELEASE Image Signature Verification Successful.
Package Load Test Latency : 8324 msec
Image validated
Detected old ROMMON version 15.4(3r)S5, upgrade required
Upgrading to newer ROMMON version required by this version of IOS-XE, do not power cycle the system.  A reboot will automatically occur for the new ROMMON to take effect.
Booted : 0
Selected : 0
Reset Reason: 0
Switching to ROM 1
Upgrading ROMMON image...
Verifying ROMMON image...
Switching back to ROM 0
ROMMON upgrade was successful...
Copying ROMMON environment...
Switching to ROM 1
Updating ROMMON environment...
Switching back to ROM 0
ROMMON upgrade complete.
To make the new ROMMON permanent, you must restart the RP.
ROMMON upgrade successful.  Rebooting for upgrade to take effect.


Initializing Hardware ...

System integrity status: 00300610
Rom image verified correctly


System Bootstrap, Version 15.4(3r)S5, RELEASE SOFTWARE
Copyright (c) 1994-2015  by cisco Systems, Inc.

Current image running: Boot ROM0

Last reset cause: LocalSoft
Cisco ISR4321/K9 platform with 4194304 Kbytes of main memory

Rommon upgrade requested
Flash upgrade reset 0 in progress
.......
Initializing Hardware ...

Checking for PCIe device presence...done
System integrity status: 0x300610
Rom image verified correctly


System Bootstrap, Version 16.4(3r), RELEASE SOFTWARE
Copyright (c) 1994-2017  by cisco Systems, Inc.


Current image running: *Upgrade in progress* Boot ROM1

Last reset cause: BootRomUpgrade
ISR4321/K9 platform with 4194304 Kbytes of main memory

Any ideas?

6 REPLIES 6
burleyman
Collaborator

Try this...

boot system flash bootflash:isr4300-universalk9.16.06.02.SPA.bin

I think the syntax is the issue.

 

Mike

First of course you need to do this...

no boot bootflash:isr4300-universalk9.16.06.02.SPA.bin

 

mike

Hulk8647
Beginner

Looks like the same solution, great. Glad you got it resolved.

 

Mike

Now I'm having  a different issue, i cannot delete the tftp from bootvar

Router(config)#do sh bootvar
BOOT variable = tftp:\\\\\\\\\\\\\\\\\\\ 255.255.255.255,12;bootflash:/isr4300-universalk9.16.06.02.SPA.bin,12;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
Configuration register is 0x2102

I tried replacing it with

boot system flash bootflash:isr4300-universalk9.16.06.02.SPA.bin

Can't do it

 

You need to run the command...

clear configure boot

 

and then put the correct boot config in.

 

Mike