Re: Cisco 7600 Stuck in rommon Mode

rajafurqan2011 · ‎07-22-2024

System Bootstrap, Version 12.2(33r)SRE, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2011 by cisco Systems, Inc.
C7600-RSP720/SP platform with 1048576 Kbytes of main memory

Autoboot executing command: "boot disk0:c7600rsp72043-adventerprisek9-mz.152-2.S 2.bin"

Initializing ATA monitor library...

Self extracting the image... [OK]
Self decompressing the image : ################################################################################################################################################################################################################################################################################################### [OK]
*** No sreloc section
Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, c7600rsp72043_sp Software (c7600rsp72043_sp-ADVENTERPRISEK9-M), Version 15.2(2)S2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 07-Aug-12 10:16 by prod_rel_team

*Jan 8 09:00:23.759: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.

*Jan 8 09:00:22.947: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor

*Jan 8 09:00:23.759: %OIR-SP-6-CONSOLE: Changing console ownership to route processor

System Bootstrap, Version 12.2(33r)SRE, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2011 by cisco Systems, Inc.

Reading monitor variables from NVRAM
Reset reason 0x0 System Reset by Power On.

Enabling interrupts
Initializing main memory
Initializing ATA controller

Exiting init
C7600-RSP720/RP platform with 2097152 Kbytes of main memory

Download Start
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Download Completed! Booting the image.
reg_v0: 0x00000000
reg_k0: 0x04013334
reg_k1: 0x20000000
tar_start: 0x00000000
tar_size: 0x00000000
Tar image address is : 0x04013334
tar size is :0x00000000
Tar magic : Tar filename : memsize : 0x80000000
Tar gid : Tar uncomp_size : 0x00000000
Tar mtime : Tar username : Tar comp_checksum : 0x00000000
Tar group name : Tar prefix : tar_size in czip : 0x00000000
Stack pointer : 0x80000000
monstack : 0x0400890C
monra : 0x00000000
edata : 0x20008780
magic : 0xFEEDFACE
memsize : 0x80000000
uncomp_size : 0x09AB73B4
comp_size : 0x0231EC88
comp_checksum : 0x2E72C371
uncomp_checksum : 0xFB2702D3
Compressed IOS src copy is : 0x20008794
compressed IOS src is : 0x7DCD8B78
IOS uncompressed dest copy is : 0x200341A0
Self decompressing the image : ################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################### [OK]
e_shoff :
0x09AB71D4
e_flags : 0x00000000
e_phnum :
0x00000001
Source elf_hdr->e_shnum = 0x0000000C
*** No sreloc sectionSetting up to copy ELF section 0x00000001
to image_info section 0x00000000
sh_name = 0x00000010
sh_type = 0x00000001
sh_flags = 0x00000007
sh_addr = 0x08000000
sh_offset = 0x00000060
sh_size = 0x08000000
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000020
sh_entsize = 0x00000000
Setting up to copy ELF section 0x00000003
to image_info section 0x00000001
sh_name = 0x0000001B
sh_type = 0x00000001
sh_flags = 0x00000003
sh_addr = 0x10000000
sh_offset = 0x08000060
sh_size = 0x01AB6F74
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000008
sh_entsize = 0x00000000
Setting up to copy ELF section 0x00000005
to image_info section 0x00000002
sh_name = 0x00000021
sh_type = 0x00000001
sh_flags = 0x00000007
sh_addr = 0x11AB6F74
sh_offset = 0x09AB6FD4
sh_size = 0x0000017C
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000004
sh_entsize = 0x00000004
Setting up to copy ELF section 0x00000006
to image_info section 0x00000003
sh_name = 0x0000002B
sh_type = 0x00000001
sh_flags = 0x00000003
sh_addr = 0x11AB70F0
sh_offset = 0x09AB7150
sh_size = 0x00000014
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000004
sh_entsize = 0x00000000
Setting up to copy ELF section 0x00000008
to image_info section 0x00000004
sh_name = 0x00000032
sh_type = 0x00000001
sh_flags = 0x00000003
sh_addr = 0x11AB7104
sh_offset = 0x09AB7164
sh_size = 0x0000002C
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000001
sh_entsize = 0x00000000
cpu type : 0x0000002C
uncomp_size : 0x09AB73B4
monstack : 0x0400890C

image_info.entry_point = 0x08000000
image_info.section_count = 0x00000005
image_info.monstack = 0x0400890C
image_info.monra = 0x00000000
image_info.param0 = 0x00000002
image_info.param1 = 0x00000000
image_info.param2 = 0x00000000
image_info.param3 = 0x00000000
image_info.reg_k0 = 0x04013334
image_info.reg_k1 = 0x00000000
Section Index = 0x00000000
source = 0x20034200
dest = 0x08000000
bytes = 0x08000000
Section Index = 0x00000001
source = 0x28034200
dest = 0x10000000
bytes = 0x01AB6F74
Section Index = 0x00000002
source = 0x29AEB174
dest = 0x11AB6F74
bytes = 0x0000017C
Section Index = 0x00000003
source = 0x29AEB2F0
dest = 0x11AB70F0
bytes = 0x00000014
Section Index = 0x00000004
source = 0x29AEB304
dest = 0x11AB7104
bytes = 0x0000002C

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.2(2)S2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 07-Aug-12 10:08 by prod_rel_team

*Jan 8 09:03:29.131: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.

*Jan 8 09:00:24.075: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.

Firmware compiled 28-Mar-12 14:56 by integ Build [100]

*Jan 8 09:03:29.131: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor

%Software-forced reload

09:03:29 UTC Sat Jan 8 2000: Unexpected exception to CPU: vector 1500, PC = 0x83D5B4C , LR = 0x83D5AE4

-Traceback= 0x83D5B4Cz 0x83D5AE4z 0x8E8300Cz 0x8E83B94z 0x8E83CD4z 0x8E398A0z 0x8E35468z 0x83D6288z 0x83D16F4z

CPU Register Context:
MSR = 0x00029200 CR = 0x42002022 CTR = 0x00000000 XER = 0x00000000
R0 = 0x083D5AE4 R1 = 0x14576DB8 R2 = 0xFFFCFFFC R3 = 0x11ECE868
R4 = 0x0A309938 R5 = 0x0000003A R6 = 0x0000004C R7 = 0x66666667
R8 = 0x00000009 R9 = 0x00000000 R10 = 0x0D720000 R11 = 0x0000004B
R12 = 0x000003E8 R13 = 0x04044000 R14 = 0x08E35328 R15 = 0x00000000
R16 = 0x00000000 R17 = 0x00000000 R18 = 0x00000000 R19 = 0x00000000
R20 = 0x00000000 R21 = 0x00000000 R22 = 0x00000000 R23 = 0x00000000
R24 = 0x00000000 R25 = 0x00000000 R26 = 0x00000000 R27 = 0x00000000
R28 = 0x0D720000 R29 = 0x14576DD0 R30 = 0x0E6E5DC0 R31 = 0x00000000

962 Unused bytes of context save spaceFile _20000108-090329-UTC Device Error :No such device

*Jan 8 09:03:30.671: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.

*Jan 8 09:03:29.563: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.

*Jan 8 09:03:29.563: %PFREDUN-SP-4-AUTOBOOT: Disable autoboot for Supervisor in slot 6
*Jan 8 09:03:29.563: %PFREDUN-SP-6-ACTIVE: Sup in slot 6 is crashing due to RP failed to boot
*Jan 8 09:03:29.595: %DIAG-SP-3-CARD_ABSENT:▒S( is not detected
*Jan 8 09:03:29.599: SP: Failed to send heartbeat poison message
*Jan 8 09:03:30.671: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor

*** System received a Software forced crash ***
signal= 0x17, code= 0x1500, context= 0xd75f9a8
PC = 0x83d5b4c, Vector = 0x1500, SP = 0x14576db8

System Bootstrap, Version 12.2(33r)SRE, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2011 by cisco Systems, Inc.
C7600-RSP720/SP platform with 1048576 Kbytes of main memory

rommon 1 >

marce1000 · ‎07-22-2024

- FYI : https://bst.cloudapps.cisco.com/bugsearch/bug/CSCuv86632
Try to boot the latest software version available for the device from USB , if not possible
or not available , contact TAC

M.

-- Each morning when I wake up and look into the mirror I always say ' Why am I so brilliant ? '
When the mirror will then always repond to me with ' The only thing that exceeds your brilliance is your beauty! '

Ramblin Tech · ‎07-22-2024

Looks like slot 6 RP (MSFC) is failing to boot, causing a crash of the slot 6 SP. Do you have redundant Sups? If so, back out the slot 6 module and try booting the chassis on the alternate Sup. If you do not have a redundant Sup in the chassis, do you have a spare somewhere that you can swap in? If no spare, try re-seating the slot 6 Sup and reload.

In any event, you should be immediately trying to obtain funding from your management for replacement of all your 7600s that carry mission-critical traffic; they have been End-of-Sale for 8 years and End-of-Support for 3 years. In my Cisco career, we had access to customer-returned equipment to stock our labs, needing only to pay for the shipping from the internal "Repo Depot" sites. I would probably go through 6 to 8 Sup720 modules before finding one that would successfully boot. You should not trust any used 7600 module that you might find for sale over the Internet as a replacement for this module.

Disclaimers: I am long in CSCO. Bad answers are my own fault as they are not AI generated.

Leo Laohoo · ‎07-22-2024

@rajafurqan2011 wrote:

*Jan 8 09:03:29.563: %PFREDUN-SP-4-AUTOBOOT: Disable autoboot for Supervisor in slot 6
*Jan 8 09:03:29.563: %PFREDUN-SP-6-ACTIVE: Sup in slot 6 is crashing due to RP failed to boot
*Jan 8 09:03:29.595: %DIAG-SP-3-CARD_ABSENT:▒S( is not detected

While in ROMMON, post the complete output to the command "set".

Is this a "brand new" or "recently acquired" supervisor card or is the supervisor card been there long?

rajafurqan2011 · ‎07-23-2024

rommon 8 > set
PS1=rommon ! >
RELOAD_TYPE=1
BSI=0
CRASHINFO=crashinfo_FAILED
BOOT=disk0:c7600rsp72043-adventerprisek9-mz.152-2.S2.bin
RET_2_RTS=04:13:30 UTC Wed Jan 5 2000
RET_2_RCALTS=947045612
?=0
PF_REDUN_CRASH_COUNT=2

rajafurqan2011 · ‎07-23-2024

rommon 5 > set
PS1=rommon ! >
RELOAD_TYPE=1
BSI=0
CRASHINFO=crashinfo_FAILED
RET_2_RTS=04:13:30 UTC Wed Jan 5 2000
RET_2_RCALTS=947045612
BOOT=disk0:c7600rsp72043-adventerprisek9-mz.122-33.SRE2.bin
PF_REDUN_CRASH_COUNT=0
?=0

___________________________

rommon 7 > boot disk0:

Initializing ATA monitor library...
string is disk0:c7600rsp72043-adventerprisek9-mz.122-33.SRE2.bin

Initializing ATA monitor library...

Self extracting the image... [OK]
Self decompressing the image : ######################################################################################################################################################################################################################################################################## [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, c7600rsp72043_sp Software (c7600rsp72043_sp-ADVENTERPRISEK9-M), Version 12.2(33)SRE2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 05-Aug-10 20:13 by prod_rel_team

*Jan 9 06:48:36.983: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.

*Jan 9 06:48:36.523: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor

*Jan 9 06:48:36.983: %OIR-6-CONSOLE: Changing console ownership to route processor

System Bootstrap, Version 12.2(33r)SRE, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2011 by cisco Systems, Inc.

Reading monitor variables from NVRAM
Reset reason 0x0 System Reset by Power On.

Enabling interrupts
Initializing main memory
Initializing ATA controller
Warning: Bootdisk is not fully plugged-in !!

Exiting init
C7600-RSP720/RP platform with 2097152 Kbytes of main memory

Download Start
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Download Completed! Booting the image.
reg_v0: 0x00000000
reg_k0: 0x04013334
reg_k1: 0x20000000
tar_start: 0x00000000
tar_size: 0x00000000
Tar image address is : 0x04013334
tar size is :0x00000000
Tar magic : Tar filename : memsize : 0x80000000
Tar gid : Tar uncomp_size : 0x00000000
Tar mtime : Tar username : Tar comp_checksum : 0x00000000
Tar group name : 4lTar prefix : tar_size in czip : 0x00000000
Stack pointer : 0x80000000
monstack : 0x0400890C
monra : 0x00000000
edata : 0x20008800
magic : 0xFEEDFACE
memsize : 0x80000000
uncomp_size : 0x0954196C
comp_size : 0x01D4A806
comp_checksum : 0x69B33AE9
uncomp_checksum : 0x5041B650
Compressed IOS src copy is : 0x20008814
compressed IOS src is : 0x7E2ACFF8
IOS uncompressed dest copy is : 0x20034260
Self decompressing the image : ##################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################### [OK]
e_shoff :
0x095417DC
e_flags : 0x00000000
e_phnum :
0x00000001
Source elf_hdr->e_shnum = 0x0000000A
Setting up to copy ELF section 0x00000001
to image_info section 0x00000000
sh_name = 0x0000000B
sh_type = 0x00000001
sh_flags = 0x00000007
sh_addr = 0x08000000
sh_offset = 0x00000060
sh_size = 0x08000000
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000020
sh_entsize = 0x00000000
Setting up to copy ELF section 0x00000003
to image_info section 0x00000001
sh_name = 0x00000019
sh_type = 0x00000001
sh_flags = 0x00000003
sh_addr = 0x10000000
sh_offset = 0x08000060
sh_size = 0x01541550
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000008
sh_entsize = 0x00000000
Setting up to copy ELF section 0x00000004
to image_info section 0x00000002
sh_name = 0x0000001F
sh_type = 0x00000001
sh_flags = 0x00000003
sh_addr = 0x11541550
sh_offset = 0x095415B0
sh_size = 0x00000058
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000004
sh_entsize = 0x00000000
Setting up to copy ELF section 0x00000005
to image_info section 0x00000003
sh_name = 0x0000002B
sh_type = 0x00000001
sh_flags = 0x00000003
sh_addr = 0x115415A8
sh_offset = 0x09541608
sh_size = 0x00000028
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000001
sh_entsize = 0x00000000
Setting up to copy ELF section 0x00000006
to image_info section 0x00000004
sh_name = 0x00000032
sh_type = 0x00000001
sh_flags = 0x00000003
sh_addr = 0x115415D0
sh_offset = 0x09541630
sh_size = 0x00000168
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000004
sh_entsize = 0x00000000
cpu type : 0x0000002C
uncomp_size : 0x0954196C
monstack : 0x0400890C

image_info.entry_point = 0x08000000
image_info.section_count = 0x00000005
image_info.monstack = 0x0400890C
image_info.monra = 0x00000000
image_info.param0 = 0x00000002
image_info.param1 = 0x00000000
image_info.param2 = 0x00000000
image_info.param3 = 0x00000000
image_info.reg_k0 = 0x04013334
image_info.reg_k1 = 0x00000000
Section Index = 0x00000000
source = 0x200342C0
dest = 0x08000000
bytes = 0x08000000
Section Index = 0x00000001
source = 0x280342C0
dest = 0x10000000
bytes = 0x01541550
Section Index = 0x00000002
source = 0x29575810
dest = 0x11541550
bytes = 0x00000058
Section Index = 0x00000003
source = 0x29575868
dest = 0x115415A8
bytes = 0x00000028
Section Index = 0x00000004
source = 0x29575890
dest = 0x115415D0
bytes = 0x00000168

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 12.2(33)SRE2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 05-Aug-10 20:01 by prod_rel_team

*Jan 9 06:51:41.711: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.

*Jan 9 06:48:37.291: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.

Firmware compiled 30-Apr-10 19:57 by integ Build [100]

*Jan 9 06:51:41.711: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor

%Software-forced reload

06:51:42 UTC Sun Jan 9 2000: Unexpected exception to CPU: vector 1500, PC = 0x8359918 , LR = 0x83598DC

-Traceback= 0x8359918 0x83598DC 0x8C34CD0 0x8C35EF4 0x8C36060 0x8BF409C 0x8BEF04C 0x835B498 0x8355774

CPU Register Context:
MSR = 0x00029200 CR = 0x40000042 CTR = 0x08E2E61C XER = 0x00000000
R0 = 0x083598DC R1 = 0x11E9B900 R2 = 0xFFFCFFFC R3 = 0x102DDF78
R4 = 0x09EB84B9 R5 = 0xFFFFFFFF R6 = 0x0000004C R7 = 0x11E429A0
R8 = 0x66666667 R9 = 0x00000000 R10 = 0x2D0D7C70 R11 = 0x0D21936C
R12 = 0x0002E4C0 R13 = 0x04044000 R14 = 0x08BEEF20 R15 = 0x00000000
R16 = 0x00000000 R17 = 0x00000000 R18 = 0x00000000 R19 = 0x00000000
R20 = 0x00000000 R21 = 0x00000000 R22 = 0x00000000 R23 = 0x00000000
R24 = 0x00000000 R25 = 0x00000000 R26 = 0x00000000 R27 = 0x00000000
R28 = 0x00000003 R29 = 0x11E9B920 R30 = 0x0E1199A8 R31 = 0x00000000

------------------ show chunk failures ------------------

------------------ show redundancy states ------------------

File _20000109-065142-UTC Device Error :No such device

1082 Unused bytes of context save space
*Jan 9 06:51:43.443: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.

*Jan 9 06:51:42.139: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.

*Jan 9 06:51:42.139: %PFREDUN-SP-4-AUTOBOOT: Disable autoboot for Supervisor in slot 6
*Jan 9 06:51:42.139: %PFREDUN-SP-6-ACTIVE: Sup in slot 6 is crashing due to RP failed to boot
*Jan 9 06:51:42.175: SP: Failed to send heartbeat poison message
*Jan 9 06:51:43.443: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor

*** System received a Software forced crash ***
signal= 0x17, code= 0x1500, context= 0xd248a80
PC = 0x8359918, Vector = 0x1500, SP = 0x11e9b900
rommon 8 >

Giuseppe Larosa · ‎07-23-2024

Hello @rajafurqan2011 ,

please note the following line :

>> Warning: Bootdisk is not fully plugged-in !!

is disk0: an external ATA ?

if not the previous message may be meaningful for you.

if the disk is not working properly the image may be corrupted in loading to RAM memory and this will make the RSP to crash.

Hope to help

Giuseppe