Re: Errors in Cisco 2950 switch

govindsingh · ‎12-07-2006

Hi,

below is the copy of log generated on switch 2950, the access switch. The interfaces are flapping after a regular interval of time although no major input / output errors are seen and no production impact.

.Dec 7 12:02:02.042: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern

et0/1, changed state to down

.Dec 7 12:02:06.182: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern

et0/1, changed state to upcpd_reset_port_config: xcvr_reset_port_config error

.Dec 7 12:48:42.715: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern

et0/33, changed state to down

.Dec 7 12:48:45.875: %LINK-3-UPDOWN: Interface FastEthernet0/33, changed state

to downcpd_reset_port_config: xcvr_reset_port_config error

.Dec 7 12:48:55.707: %LINK-3-UPDOWN: Interface FastEthernet0/33, changed state

to up

.Dec 7 12:48:56.707: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern

et0/33, changed state to upcpd_reset_port_config: xcvr_reset_port_config error

.Dec 7 15:36:09.539: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern

et0/11, changed state to down

.Dec 7 15:36:14.483: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern

et0/11, changed state to upcpd_reset_port_config: xcvr_reset_port_config error

.Dec 7 15:37:04.519: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern

et0/11, changed state to down

.Dec 7 15:37:07.687: %LINK-3-UPDOWN: Interface FastEthernet0/11, changed state

to down

.Dec 7 15:37:19.891: %LINK-3-UPDOWN: Interface FastEthernet0/11, changed state

to up

.Dec 7 15:37:20.899: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern

et0/11, changed state to upcpd_reset_port_config: xcvr_reset_port_config error

.Dec 7 15:37:45.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern

et0/11, changed state to down

.Dec 7 15:37:50.519: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern

et0/11, changed state to upcpd_reset_port_config: xcvr_reset_port_config error

.Dec 7 15:46:21.230: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern

et0/11, changed state to down

.Dec 7 15:46:24.390: %LINK-3-UPDOWN: Interface FastEthernet0/11, changed state

to down

Any idea...

rgds

govind

ankbhasi · ‎12-07-2006

Hi Govind,

Which image version you are running on the switch?

There is a bug for these kind of error messages and the bug id is "CSCee89453"

Which is described as below

When full duplex is provisioned on the Gig SFP 10/100/1000BaseTX port, evertime

the link goes down or comes up via disconnect or shut/no shut on other side of

port (the switch it is connected to), the following error message is diplayed

and sent to the log: "cpd_reset_port_config: xcvr_reset_port_config error". The

new speed and duplex enhancements may draw more attention to these types of

bugs.

This is Integrated in: 12.1(22)EA2

So try upgrading your switch and see if that resolves the issue.

HTH

Ankur

*Pls rate helpfull post

govindsingh · ‎12-08-2006

Hi Ankur,

Thanks for your input.

following is the output of sh version. we using 12.1(19)EA1a.bin

Cisco Internetwork Operating System Software

IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(19)EA1a, RELEASE SOFTWAR

(fc1)

Compiled Tue 09-Dec-03 00:12 by yenanh

Image text-base: 0x80010000, data-base: 0x8058A000

ROM: Bootstrap program is C2950 boot loader

Site1_TF_08 uptime is 1 year, 9 weeks, 5 days, 21 hours, 3 minutes

System returned to ROM by power-on

System restarted at 06:33:59 BST Sat Oct 1 2005

System image file is "flash:c2950-i6q4l2-mz.121-19.EA1a.bin"

cisco WS-C2950G-48-EI (RC32300) processor (revision D0) with 20809K bytes of me

ory.

Processor board ID FOC0636W03J

Last reset from system-reset

Running Enhanced Image

48 FastEthernet/IEEE 802.3 interface(s)

2 Gigabit Ethernet/IEEE 802.3 interface(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:0A:F4:1D:D0:40

System returned to ROM by power-on

System restarted at 06:33:59 BST Sat Oct 1 2005

System image file is "flash:c2950-i6q4l2-mz.121-19.EA1a.bin"

cisco WS-C2950G-48-EI (RC32300) processor (revision D0) with 20809K bytes of mem

ory.

Processor board ID FOC0636W03J

Last reset from system-reset

Running Enhanced Image

48 FastEthernet/IEEE 802.3 interface(s)

2 Gigabit Ethernet/IEEE 802.3 interface(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:0A:F4:1D:D0:40

Motherboard assembly number: 73-7409-09

Power supply part number: 34-0965-01

Motherboard serial number: FOC06350U0M

Power supply serial number: DAB063578B7

Model revision number: D0

Motherboard revision number: A0

Model number: WS-C2950G-48-EI

System serial number: FOC0636W03J

Configuration register is 0xF

I m not able to access the bug details which you have mentioned.

switch is giving this error intermittently. no shut/no shut is being performed in other end.

I will upgrade the ios and update you for the same

regds

govind

MichaelVolkmer · ‎05-22-2007

Hi Govind,

today i ran into the same problem - and after the suggested IOS update the message is gone.

But the device still dis/- and reconnects constantly. I'll replace the NIC of the device tomorrow and check it again.

Did you had a look at the interface counters - especially the errors? ( 'mine' has a lots of errors)

Cheers

Michael