cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Community Helping Community

5546
Views
0
Helpful
9
Replies

load balancing with PBR & failover with IPsla

in my organization i want to load balance duel  WAN link also want to ensure Fail over with IP SLA. can you give some idea how it can be down. what i did better i will explain firstly ........

i did load balancing with PBR and its working fine. for example there are two VLAN in my organization .First 1. VLan 10 & 2nd is Vlan 20 . I want Vlan 10 goes in ISP 1 and VLAN 20 goes in ISP 2  & its working fine . but the prbolem is when i want to configure IPSLA for fail over then its create problem like i want to, if ISP 1 is down VLAN 10 data will go on ISP 2  , But if ISP 2 is down then vlan 20  does not go on  ISP 1 . Can any one give some idea......how it can be done .......

         


Oval: ISP 1
Everyone's tags (2)
1 ACCEPTED SOLUTION

Accepted Solutions
Rising star

load balancing with PBR & failover with IPsla

Hi,

For such thing you need to track object with IP SLA both ISPs. And match to PBRs.

Refer to this example https://supportforums.cisco.com/docs/DOC-8313

Hope it will help.

Hope it will help. Best regards, Abzal

View solution in original post

9 REPLIES 9
Advisor

load balancing with PBR & failover with IPsla

Hi,

Can you post your config.

Regards.

Alain

Don't forget to rate helpful posts.

Don't forget to rate helpful posts.

load balancing with PBR & failover with IPsla

ip route 0.0.0.0 0.0.0.0 x.x.x.x

ip route 0.0.0.0 0.0.0.0 x.x.x.x 10

route-map Duel-Link-route permit 1

match ip address 20

set ip default next-hop ISP 1 Peer IP

route-map Duel-Link-route permit 1

match ip address 30

set ip default next-hop ISP 2 Peer IP

this is PBR configuration with i did in My router , BUT can you explain how i can implement IPSLA with this senario

Rising star

load balancing with PBR & failover with IPsla

Hi,

For such thing you need to track object with IP SLA both ISPs. And match to PBRs.

Refer to this example https://supportforums.cisco.com/docs/DOC-8313

Hope it will help.

Hope it will help. Best regards, Abzal

View solution in original post

Highlighted

load balancing with PBR & failover with IPsla

can you send us ISP connectivity topology? does ISP connected directly on CORE or Router?

may below page help you -

https://supportforums.cisco.com/message/3788769#3788769

load balancing with PBR & failover with IPsla

thanks to all but can you give me idea 2821 router which Image capable for configure IP SLA , bcz my 2821 router image is

"flash:c2800nm-ipbase-mz.150-1.M3.bin" , where is no feature of IPSLA configuration.

load balancing with PBR & failover with IPsla

thanks to all but can you give me idea 2821 router which Image capable for configure IP SLA , bcz my 2821 router image is

"flash:c2800nm-ipbase-mz.150-1.M3.bin" , where is no feature of IPSLA configuration.

Advisor

load balancing with PBR & failover with IPsla

Hi,

you need 15.1(2)T , take a look here to which are available images:http://tools.cisco.com/ITDIT/CFN/jsp/by-feature-technology.jsp

Regards.

Alain

Don't forget to rate helpful posts.

Don't forget to rate helpful posts.

load balancing with PBR & failover with IPsla

Thanks Abzal , Nice explanation documment ......

Beginner

Re: load balancing with PBR & failover with IPsla

Hi Abzal,

I am unable to check the article, it giving me access denied on my ID, can you please post the article here.
CreatePlease to create content
Content for Community-Ad