03-27-2012 07:55 AM - edited 03-07-2019 05:48 AM
Hi
I am trying to create a new vlan 2 on my switch 2960, when I go into the interface where I want the encapsulation command its not there? sh version command is:
CISCO2960#show ver
Cisco IOS Software, C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE,
RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Sat 07-Aug-10 23:21 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x01B00000
ROM: Bootstrap program is Alpha board boot loader
BOOTLDR: C2960S Boot Loader (C2960S-HBOOT-M) Version 12.2(53r)SE, RELEASE SOFTWA
RE (fc3)
CISCO2960 uptime is 10 weeks, 6 days, 14 hours, 15 minutes
System returned to ROM by power-on
System image file is "flash:/c2960s-universalk9-mz.122-53.SE1/c2960s-universalk9
-mz.122-55.SE.bin"
cisco WS-C2960S-48TS-S (PowerPC) processor (revision A0) with 131072K bytes of m
emory.
Processor board ID FOC1416Z55B
Last reset from power-on
2 Virtual Ethernet interfaces
1 FastEthernet interface
50 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 9C:4E:20:79:A4:00
Motherboard assembly number : 73-12424-05
Power supply part number : 341-0327-01
Motherboard serial number : FOC14164ATM
Power supply serial number : DCA1351P01J
Model revision number : A0
Motherboard revision number : A0
Model number : WS-C2960S-48TS-S
Daughterboard assembly number : 73-11933-04
Daughterboard serial number : FOC14170D12
System serial number : FOC1416Z55B
Top Assembly Part Number : 800-32452-01
Top Assembly Revision Number : A0
Version ID : V01
CLEI Code Number : COMGK00ARA
Daughterboard revision number : A0
Hardware Board Revision Number : 0x01
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 50 WS-C2960S-48TS-S 12.2(55)SE C2960S-UNIVERSALK9-M
Configuration register is 0xF
Here is what I am trying to do:
CISC(config)#inter
CISC(config)#interface gig
CISC(config)#interface gigabitEthernet 0/23
C(config-if)#swi
ISC(config-if)#switchport tru
SC(config-if)#switchport trunk en
ISC(config-if)#switchport trunk enca
ISC(config-if)#switchport trunk encapsulation dot1q
ISC(config-if)#switchport trunk encapsulation dot1q
^
% Invalid input detected at '^' marker.ISC(config-if)#switchport trunk encapsulation dot1q
^
% Invalid input detected at '^' marker.
Why the encapsulation command not there help please. Please see attached I have connected my laptop with port 23 of this switch where I am trying to have vlan 2, since I am unable to have the encapsulation command I do not get any IP.
03-27-2012 10:29 AM
Vijay,
1. Correct all the clients and the dhcp server is connected to the same switch 2960 (For location 1) , (location 2 has their own switch 2960).
2.Correct my laptop is connected to port 23 of the switch 2960. where I want Vlan2 to be operative.
3. I just checked sh int vlan2 and its up and up
4. Correct the dhcp is connected physically to port 1 of the switch 2960. So you mean I have to offer the command 'switch port access vLan2 on port 1'? I thought the ip-helper command finds the DHCP for that particular vlan2?
Please let me know I can command the port 1 to access VLan2?
03-27-2012 10:40 AM
Yes. Exactly.. The IP Helper address would just tell where is the dhcp server located at. but for the dhcp server to receive your laptop's request it has to be a part of vlan 2 or a link which allows vlan 2 traffic to come
HTH
-Vijay
03-27-2012 10:21 AM
Jan,
You mean offering
ip helper 10.10.10.96 255.255.255.0 or
ip helper 10.10.2.1 255.255.255.0 on the router interface? 0/1.801 which is connected to location 1? I can do that, here is the part config of my router 2911:
interface GigabitEthernet0/0 <<<<<..................location 2 interface
description B_CAMPUS_LAN
ip address 10.10.11.254 255.255.255.0
no ip redirects
no ip unreachables
ip nbar protocol-discovery
ip flow ingress
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
no cdp enable
!
!
interface GigabitEthernet0/1
no ip address
ip nbar protocol-discovery
ip flow ingress
duplex full
speed 100
no cdp enable
!
!
interface GigabitEthernet0/1.92 <<<<<......................our internet
description INTERNET
encapsulation dot1Q 92
ip address 7x.xx.xx.xxx 255.255.255.254
ip access-group 101 in
no ip redirects
no ip unreachables
ip nbar protocol-discovery
ip flow ingress
ip nat outside
ip inspect TRAFFIC_INSPECTI out
ip virtual-reassembly
no cdp enable
service-policy input block-p2p
!
interface GigabitEthernet0/1.801 <<<<............this subinterface is connected to location 1 where I want the vlan2
description O_CAMPUS_LAN
encapsulation dot1Q 801
ip address 10.10.2.254 255.255.255.0 secondary
ip address 10.10.10.254 255.255.255.0
no ip redirects
no ip unreachables
ip nbar protocol-discovery
ip flow ingress
ip flow egress
ip nat inside
ip virtual-reassembly
no cdp enable
!
interface GigabitEthernet0/2 <<<<...........not connected vacant
description $ES_LAN$
no ip address
shutdown
duplex auto
speed auto
03-27-2012 10:31 AM
Hi Adnan,
I mean like creating subinterface such as:
interface GigabitEthernet0/1.2
encapsulation dot1Q 2
ip address 10.10.2.254 255.255.255.0
ip helper-address 10.10.10.96
I am sorry but I do not understand why you have subif with tags of vlan801. Can you please tell us?
Another good sugestion was mentioned here - if you want just users from vlan2 to have dhcp services, you can add port where the DHCP server is to the vlan2. Then the switch will redistribute broadcast in the same vlan and users will get an IP address.
To do that simply make this on the switch:
interface GigabitEthernet0/1
swicthport mode access
switchport access vlan2
But in this case, you won't be able to offer DHCP services to other clients than from vlan2.
Best regards,
Jan
03-27-2012 10:50 AM
Hi Jan,
"""I am sorry but I do not understand why you have subif with tags of vlan801. Can you please tell us?"""The config was created long time back, only thing I know about this is that 0/1.801 is our interface which is connected to our location. Not sure if this is good or bad.
When I apply these commands to port 1:
interface GigabitEthernet0/1
swicthport mode access
switchport access vlan2
Then my DHCP server could not go online (internet), my laptop gets the IP this way. Help
03-27-2012 11:00 AM
Hi Adnan,
sure. The PC can get to the internet? If the answer is yes - then maybe it is becase of access-list. What ACL is configured on the router for NAT?
Best regards,
Jan
03-27-2012 11:08 AM
Jan,
Just to re-confirm, by putting the port 1 on vlan2, the DHCP server cannot go online. The router is using access-list 101 in.
03-27-2012 11:10 AM
Hi Adnan,
yes I got that . Can the PC get to internet? Can you please post the access-list 101, how it looks like?
Best regards,
Jan
03-27-2012 11:18 AM
show ip access-lists
Standard IP access list 10
10 permit 10.10.0.0, wildcard bits 0.0.255.255 (575457054 matches)
Standard IP access list 21
10 permit any (5837861 matches)
Standard IP access list 23
10 permit 10.10.10.0, wildcard bits 0.0.0.7
Standard IP access list 50
10 permit 72.xx.xx.xxx
20 permit 10.10.10.0, wildcard bits 0.0.0.255
30 permit 10.10.11.0, wildcard bits 0.0.0.255
Extended IP access list 101
10 deny ip 72.184.0.0 0.0.0.255 any
20 deny ip 88.201.0.0 0.0.255.255 any (33 matches)
30 deny ip 195.211.0.0 0.0.255.255 any (257 matches)
40 deny ip 222.173.0.0 0.0.255.255 any (74 matches)
50 deny ip 211.78.0.0 0.0.255.255 any (6 matches)
60 deny ip 201.12.0.0 0.0.255.255 any (56 matches)
70 deny ip 183.57.0.0 0.0.255.255 any (3 matches)
80 deny ip 177.39.0.0 0.0.255.255 any (15 matches)
90 deny ip 189.101.0.0 0.0.255.255 any (74 matches)
100 deny ip 71.98.246.0 0.0.0.255 any
110 deny ip 199.117.155.0 0.0.0.255 any
120 deny ip 84.254.0.0 0.0.255.255 any (15 matches)
130 deny ip 78.29.0.0 0.0.255.255 any (308 matches)
140 deny ip 64.167.160.0 0.0.0.255 any
150 deny ip 79.126.225.0 0.0.0.255 any
160 deny ip 114.129.232.0 0.0.0.255 any
170 deny ip 195.78.0.0 0.0.255.255 any (668 matches)
180 deny ip 91.191.230.0 0.0.0.255 any
190 deny ip 69.117.48.0 0.0.0.255 any
200 deny ip 108.58.158.0 0.0.0.255 any
210 deny ip 61.144.0.0 0.0.255.255 any (140 matches)
220 deny ip 122.116.0.0 0.0.255.255 any (151 matches)
230 deny ip 124.82.0.0 0.0.255.255 any (83 matches)
240 deny ip 212.176.0.0 0.0.255.255 any
250 deny ip 175.43.68.0 0.0.0.255 any
260 deny ip 117.135.204.0 0.0.0.255 any (9 matches)
270 deny ip 64.207.56.0 0.0.0.255 any
280 deny ip 120.39.11.0 0.0.0.255 any
290 deny ip 183.62.0.0 0.0.255.255 any (48 matches)
300 deny ip 221.239.0.0 0.0.255.255 any (6 matches)
310 deny ip 189.146.0.0 0.0.255.255 any (32 matches)
320 deny ip 110.175.0.0 0.0.255.255 any (329 matches)
330 deny ip 184.22.0.0 0.0.255.255 any (3693 matches)
340 deny ip 222.66.61.0 0.0.0.255 any
350 deny ip 213.246.181.0 0.0.0.255 any (147 matches)
360 deny ip 91.140.227.0 0.0.0.255 any
370 deny ip 95.9.57.0 0.0.0.255 any
380 deny ip 157.157.80.0 0.0.0.255 any
390 deny ip 173.59.30.0 0.0.0.255 any
400 deny ip 71.87.2.0 0.0.0.255 any
410 deny ip 188.84.126.0 0.0.0.255 any
420 deny ip 70.25.122.0 0.0.0.255 any
430 deny ip 65.13.229.0 0.0.0.255 any
440 deny ip 75.25.92.0 0.0.0.255 any
450 deny ip 219.89.84.0 0.0.0.255 any
460 deny ip 71.160.30.0 0.0.0.255 any
470 deny ip 10.0.0.0 0.255.255.255 any (980 matches)
480 permit icmp any any echo (2149642 matches)
490 permit icmp any any unreachable (115638 matches)
500 permit icmp any any traceroute
510 permit icmp any any echo-reply (2005 matches)
520 permit icmp any any ttl-exceeded (28106 matches)
530 permit icmp any any time-exceeded (1 match)
540 permit icmp any any source-quench (310 matches)
550 permit icmp any any packet-too-big
560 permit ip any host 7x.xx.xxx.xxx (152447782 matches)
570 permit tcp any host 7x.xx.xxx.xxx eq 443 (36384 matches)
580 permit tcp any host 7x.xx.xxx.xxx eq www (6411 matches)
03-27-2012 11:31 AM
Hi Adnan,
just to make everything clear .
Can PC from VLAN2 get to the internet?
How is the switch connected with the router? Through gi0/1? Is the gi0/1 an trunk link?
I think that if you wish to access internet from vlan 2 and if I'm getting this right...you would need to create another subinterface for vlan2, make it ip nat inside, make an access-list to permit which addresses you want to access internet and specify to what pool or interface you want to translate these interfaces.
Best regards,
Jan
03-27-2012 11:40 AM
No the laptop does not get any internet, it has the IP though.
The switch is connected with the router on port 48. like: I do not see any trunk on port 48.
"
interface GigabitEthernet0/48
description source port
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/49
!
interface GigabitEthernet0/50
!
interface Vlan1
ip address 10.10.10.252 255.255.255.0
!
interface Vlan2
ip address 10.10.2.252 255.255.255.0
ip helper-address 10.10.2.1
!
ip default-gateway 10.10.10.254
ip http server
ip http secure-server
no cdp run
03-27-2012 11:46 AM
Hi Adnan,
So you have inherited the network and now you are configuring the new vlan, right ?
The switch is connected with the router on port 48. like: I do not see any trunk on port 48.
That is weird, I would expect that this would be trunk interface - because Router has more subinterfaces.
Before assigning the dhcp router to vlan2, it had internet conectivity? Something doesn't make sense to me here, but I hope that together we will find out what .
Best regards,
Jan
03-27-2012 12:08 PM
Jan,
Correct, for the last 10 years no trouble till we now at a situation where I need to separate the vlans. Correct before I put DHCP to port 2 I had the internet. What do you need to see now
03-27-2012 12:22 PM
Hi Adnan,
Can you please show us, what does the topology looks like? I am getting really confused how it could be set up . I'm trying to put my finger on it...
Best regards,
Jan
03-27-2012 12:36 PM
Jan,
If I can draw well:
location 1 where I am creating vlan2 ISP location 2
switch 2960........................................................... ...........................................Router 2911....(switch2960)
Please refer my layout above for the topology , I am at location 1 where vlan2 is needed it has cisco 2960 switch, location 2 is connected with us and somewhere in between comes the ISP, and here are the show vlans from both the router 2911 and the switch 2960:
show vlans form the ROUTER 2911:
Virtual LAN ID: 1 (IEEE 802.1Q Encapsulation)
vLAN Trunk Interface: GigabitEthernet0/1
This is configured as native Vlan for the following interface(s) :
GigabitEthernet0/1
Protocols Configured: Address: Received: Transmitted:
Other 0 673592
0 packets, 0 bytes input
673592 packets, 12774777 bytes output
Virtual LAN ID: 801 (IEEE 802.1Q Encapsulation)
vLAN Trunk Interface: GigabitEthernet0/1.801
Protocols Configured: Address: Received: Transmitted:
IP 10.10.10.254 659224947 535020952
Other 0 7519098
659229308 packets, 601945550557 bytes input
542540050 packets, 358253967971 bytes output
Virtual LAN ID: 92 (IEEE 802.1Q Encapsulation)
vLAN Trunk Interface: GigabitEthernet0/1.92
Protocols Configured: Address: Received: Transmitted:
IP 7x.xx.xxx.xxx 523949719 571093451
Other 0 453
523949719 packets, 429113863666 bytes input
571093904 packets, 538275489140 bytes output
***********************************************************************************************************************************
My Switch 2960 its config and show vlan:
Current configuration : 7572 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
!
CISCO2960
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
clock timezone EST -5
clock summer-time EDT recurring
authentication mac-move permit
!
--More-- !
!
!
quit
spanning-tree mode pvst
spanning-tree extend system-id
!
!
!
!
vlan internal allocation policy ascending
!
!
interface FastEthernet0
no ip address
--More-- !
interface GigabitEthernet0/1
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/2
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/3
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/4
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/5
no cdp enable
--More-- no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/6
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/7
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/8
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/9
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
--More-- interface GigabitEthernet0/10
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/11
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/12
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/13
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/14
no cdp enable
no cdp tlv server-location
--More-- no cdp tlv app
!
interface GigabitEthernet0/15
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/16
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/17
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/18
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/19
--More-- no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/20
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/21
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/22
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/23
switchport access vlan 2
switchport mode access
no cdp enable
--More-- no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/24
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/25
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/26
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/27
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
--More-- interface GigabitEthernet0/28
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/29
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/30
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/31
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/32
no cdp enable
no cdp tlv server-location
--More-- no cdp tlv app
spanning-tree portfast
!
interface GigabitEthernet0/33
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/34
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/35
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/36
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
--More-- interface GigabitEthernet0/37
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/38
switchport mode access
no cdp enable
no cdp tlv server-location
no cdp tlv app
spanning-tree portfast
!
interface GigabitEthernet0/39
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/40
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/41
--More-- no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/42
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/43
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/44
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/45
no cdp enable
no cdp tlv server-location
no cdp tlv app
--More-- !
interface GigabitEthernet0/46
no cdp enable
no cdp tlv server-location
no cdp tlv app
spanning-tree portfast
!
interface GigabitEthernet0/47
description sessnMntrPort48
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/48
description source port
no cdp enable
no cdp tlv server-location
no cdp tlv app
!
interface GigabitEthernet0/49
!
interface GigabitEthernet0/50
!
--More-- interface Vlan1
ip address 10.10.10.252 255.255.255.0
!
interface Vlan2
ip address 10.10.2.252 255.255.255.0
ip helper-address 10.10.10.96
ip helper-address 10.10.10.1
!
ip default-gateway 10.10.10.254
ip http server
ip http secure-server
no cdp run
!
!
!
end
CISCO2960#
CISCO2960#
CISCO2960#
CISCO2960#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi0/1, Gi0/2, Gi0/3, Gi0/4
Gi0/5, Gi0/6, Gi0/7, Gi0/8
Gi0/9, Gi0/10, Gi0/11, Gi0/12
Gi0/13, Gi0/14, Gi0/15, Gi0/16
Gi0/17, Gi0/18, Gi0/19, Gi0/20
Gi0/21, Gi0/22, Gi0/24, Gi0/25
Gi0/26, Gi0/27, Gi0/28, Gi0/29
Gi0/30, Gi0/31, Gi0/32, Gi0/33
Gi0/34, Gi0/35, Gi0/36, Gi0/37
Gi0/38, Gi0/39, Gi0/40, Gi0/41
Gi0/42, Gi0/43, Gi0/44, Gi0/45
Gi0/46, Gi0/48, Gi0/49, Gi0/50
2 VLAN0002 active Gi0/23
201 VLAN0201 active
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
--More-- ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
2 enet 100002 1500 - - - - - 0 0
201 enet 100201 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 tr 101003 1500 - - - - - 0 0
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trnet 101005 1500 - - - ibm - 0 0
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
CISCO2960#
CISCO2960#
CISCO2960#
CISCO2960#show ip in
CISCO2960#show ip interface br
CISCO2960#show ip interface brief
Interface IP-Address OK? Method Status Protocol
Vlan1 10.10.10.252 YES NVRAM up up
Vlan2 10.10.2.252 YES manual up up
FastEthernet0 unassigned YES NVRAM down down
GigabitEthernet0/1 unassigned YES unset up up
GigabitEthernet0/2 unassigned YES unset up up
GigabitEthernet0/3 unassigned YES unset up up
GigabitEthernet0/4 unassigned YES unset up up
GigabitEthernet0/5 unassigned YES unset down down
GigabitEthernet0/6 unassigned YES unset up up
GigabitEthernet0/7 unassigned YES unset up up
GigabitEthernet0/8 unassigned YES unset up up
GigabitEthernet0/9 unassigned YES unset up up
GigabitEthernet0/10 unassigned YES unset up up
GigabitEthernet0/11 unassigned YES unset up up
GigabitEthernet0/12 unassigned YES unset up up
GigabitEthernet0/13 unassigned YES unset up up
GigabitEthernet0/14 unassigned YES unset up up
GigabitEthernet0/15 unassigned YES unset up up
GigabitEthernet0/16 unassigned YES unset down down
GigabitEthernet0/17 unassigned YES unset up up
GigabitEthernet0/18 unassigned YES unset up up
GigabitEthernet0/19 unassigned YES unset up up
--More-- GigabitEthernet0/20 unassigned YES unset up up
GigabitEthernet0/21 unassigned YES unset up up
GigabitEthernet0/22 unassigned YES unset up up
GigabitEthernet0/23 unassigned YES unset up up
GigabitEthernet0/24 unassigned YES unset up up
GigabitEthernet0/25 unassigned YES unset up up
GigabitEthernet0/26 unassigned YES unset up up
GigabitEthernet0/27 unassigned YES unset down down
GigabitEthernet0/28 unassigned YES unset up up
GigabitEthernet0/29 unassigned YES unset up up
GigabitEthernet0/30 unassigned YES unset up up
GigabitEthernet0/31 unassigned YES unset up up
GigabitEthernet0/32 unassigned YES unset up up
GigabitEthernet0/33 unassigned YES unset up up
GigabitEthernet0/34 unassigned YES unset down down
GigabitEthernet0/35 unassigned YES unset up up
GigabitEthernet0/36 unassigned YES unset up up
GigabitEthernet0/37 unassigned YES unset up up
GigabitEthernet0/38 unassigned YES unset up up
GigabitEthernet0/39 unassigned YES unset up up
GigabitEthernet0/40 unassigned YES unset up up
GigabitEthernet0/41 unassigned YES unset up up
GigabitEthernet0/42 unassigned YES unset up up
--More-- GigabitEthernet0/43 unassigned YES unset up up
GigabitEthernet0/44 unassigned YES unset up up
GigabitEthernet0/45 unassigned YES unset up up
GigabitEthernet0/46 unassigned YES unset up up
GigabitEthernet0/47 unassigned YES unset up down
GigabitEthernet0/48 unassigned YES unset up up
GigabitEthernet0/49 unassigned YES unset down down
GigabitEthernet0/50 unassigned YES unset down down
CISCO2960#
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide