cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

301
Views
0
Helpful
4
Replies
Beginner

Question on the command "mls qos srr-queue input" command that is not supported on 2960X switch

HI everyone,

Good morning. Hope you can help.

One of my 3560E old switch crashed and we got a 2960x as a replacement. I found out that the "mlsqos srr-queue in put" command in global config will not be taken by the new 2960X switch. The following is the settings from the 3560E switch.


I would like to ask

 

1.). what commands do I need to use to replace the following commands on the new switch? May you show me how to make the configuration which will be able to substitute the following old commands?

2.) What if I miss the commands? What the effect be if I do not put in the following commands? mls qos srr-queue out can still be taken.

 

I am not good at QoS...hope you can help. Thank you for your help in advance.


Takami Chiro

 

#######################

mls qos srr-queue input bandwidth 90 10

mls qos srr-queue input threshold 1 8 16

mls qos srr-queue input threshold 2 34 66

mls qos srr-queue input buffers 67 33 

mls qos srr-queue input cos-map queue 1 threshold 2  1

mls qos srr-queue input cos-map queue 1 threshold 3  0

mls qos srr-queue input cos-map queue 2 threshold 1  2

mls qos srr-queue input cos-map queue 2 threshold 2  4 6 7

mls qos srr-queue input cos-map queue 2 threshold 3  3 5

mls qos srr-queue input dscp-map queue 1 threshold 2  9 10 11 12 13 14 15

mls qos srr-queue input dscp-map queue 1 threshold 3  0 1 2 3 4 5 6 7

mls qos srr-queue input dscp-map queue 1 threshold 3  32

mls qos srr-queue input dscp-map queue 2 threshold 1  16 17 18 19 20 21 22 23

mls qos srr-queue input dscp-map queue 2 threshold 2  33 34 35 36 37 38 39 48

mls qos srr-queue input dscp-map queue 2 threshold 2  49 50 51 52 53 54 55 56

mls qos srr-queue input dscp-map queue 2 threshold 2  57 58 59 60 61 62 63

mls qos srr-queue input dscp-map queue 2 threshold 3  24 25 26 27 28 29 30 31

mls qos srr-queue input dscp-map queue 2 threshold 3  40 41 42 43 44 45 46 47

##########

4 REPLIES 4
Rising star

Re: Question on the command "mls qos srr-queue input" command that is not supported on 2960X switch

Hello,

Some commands can be diffrent from model to model.

check here, type of commands, how to configure qos on 2960x.
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960x/software/15-0_2_EX/qos/configuration_guide/b_qos_152ex_2960-x_cg/b_qos_152ex_2960-x_cg_chapter_011.html

Dont forget mark as helpful and solved all post that help you.

Thanks in advance.
Jaderson Pessoa
*** Rate All Helpful Responses ***
Beginner

Re: Question on the command "mls qos srr-queue input" command that is not supported on 2960X switch

I think it is the default QoS setting on your 3560 switch.

Have your 3560 configured with "mls qos trust cos" or "mls qos trust dscp" on any interface? If no, the COS/DSCP value of every packet go into 3560 would be rewrote to 0. When all packets are treating as the same priority, the QoS become meaningless.

So, have a check on current 3560 setting first. If the above command is not found, I think you don't need to enable QoS on your new C2960X.

Beginner

Re: Question on the command "mls qos srr-queue input" command that is not supported on 2960X switch

Hi ngkin2010


thank you for your response. I just checked my 3560E interface settings. It has the following commands:


mls qos trust device cisco-phone
mls qos trust cos


May I ask what I should do next?

Thank you
Highlighted
Beginner

Re: Question on the command "mls qos srr-queue input" command that is not supported on 2960X switch

Your infrastructure contain VoIP, then you have to study the on current QoS marking and policing.

Why not just simply copy and paste? because the queuing model of C2960X and C3560 is different. For example C3560 have 2 ingress queue (with one of the priority queue), while C2960X have no ingress queue. So you cannot apply the same planning from C3560 to C2960X.

Yes, it's time consuming for study 3560's behavior and 2960X's behavior.

BTW, can you share us the information: show policy-map interface <interface configured with trust COS>
CreatePlease to create content
Content for Community-Ad
July's Community Spotlight Awards