Removing stacked interfaces from show RUn

joshhboss · ‎07-01-2021

So i order a few used switches and they arrived as part of a stock. I was able to remove them from the stack by just issuing a renumber command but now even tho my running config shows the correct Gi1/0/X interface names when i need to work on them.. in my actual SHOW RUN.. it still has the switches but as Gi4/0/X. How could i remove this please?

Thank you all!!

interface GigabitEthernet1/0/24
!
interface GigabitEthernet1/0/25
!
interface GigabitEthernet1/0/26
!
interface GigabitEthernet1/0/27
!
interface GigabitEthernet1/0/28
!
interface GigabitEthernet1/0/29
!
interface GigabitEthernet1/0/30
!
interface GigabitEthernet1/0/31
!
interface GigabitEthernet1/0/32
!
interface GigabitEthernet1/0/33
!
interface GigabitEthernet1/0/34
!
interface GigabitEthernet1/0/35
!
interface GigabitEthernet1/0/36
!
interface GigabitEthernet1/0/37
!
interface GigabitEthernet1/0/38
!
interface GigabitEthernet1/0/39
!
interface GigabitEthernet1/0/40
!
interface GigabitEthernet1/0/41
!
interface GigabitEthernet1/0/42
!
interface GigabitEthernet1/0/43
!
interface GigabitEthernet1/0/44
!
interface GigabitEthernet1/0/45
!
interface GigabitEthernet1/0/46
!
interface GigabitEthernet1/0/47
!
interface GigabitEthernet1/0/48
 switchport mode trunk
 ip dhcp snooping trust
!
interface GigabitEthernet1/0/49
!
interface GigabitEthernet1/0/50
!
interface GigabitEthernet1/0/51
!
interface GigabitEthernet1/0/52
!
interface GigabitEthernet4/0/1
!
interface GigabitEthernet4/0/2
!
interface GigabitEthernet4/0/3
!
interface GigabitEthernet4/0/4
!
interface GigabitEthernet4/0/5
!
interface GigabitEthernet4/0/6
!
interface GigabitEthernet4/0/7
!
interface GigabitEthernet4/0/8
!
interface GigabitEthernet4/0/9
!
interface GigabitEthernet4/0/10
!
interface GigabitEthernet4/0/11
!
interface GigabitEthernet4/0/12
!
interface GigabitEthernet4/0/13
!
interface GigabitEthernet4/0/14
!
interface GigabitEthernet4/0/15
!
interface GigabitEthernet4/0/16
!
interface GigabitEthernet4/0/17
!
interface GigabitEthernet4/0/18
!
interface GigabitEthernet4/0/19
!
interface GigabitEthernet4/0/20
!
interface GigabitEthernet4/0/21
!
interface GigabitEthernet4/0/22
!
interface GigabitEthernet4/0/23
!
interface GigabitEthernet4/0/24
!
interface GigabitEthernet4/0/25
!
interface GigabitEthernet4/0/26
!
interface GigabitEthernet4/0/27
!
interface GigabitEthernet4/

Leo Laohoo · ‎07-01-2021

conf t
 no switch 4 prov
end

Seb Rupik · ‎07-01-2021

Hi there:

!
no switch 4 provision
!

cheers,

Seb.

paul driver · ‎07-01-2021

Hello

Anohter to do this so to start off with a clean switch:

dir flash:
delete flash:config.txt
delete flash:vlan.dat

reload

Please rate and mark as an accepted solution if you have found any of the information provided useful.
This then could assist others on these forums to find a valuable answer and broadens the community’s global network.

Kind Regards
Paul