cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
300
Views
0
Helpful
4
Replies

Switch 2901 HWIC-1FE, module detect but there's no interface.

faruqfarkhan
Level 1
Level 1

Hello,

i have a 2901 router (IOS version 15.0(1)M9), I Have HWIC-1FE, systems detects this modules:

faruqfarkhan_0-1696313511834.png

But when i check show ip int br it doesn't detect the fast ethernet module interfaces:

faruqfarkhan_1-1696313613251.png

does any one know why that happened? i attached the boot up process

Thank you

 

4 Replies 4

Are you sure its supported on the C2901? The documentation dosent mention this.

DanielP211_0-1696316873164.png

https://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/ic/hardware/installation/guide/oview_ic.html

BR

****Kindly rate all useful posts*****

Hi Daniel

the link that you give is from 2007, and here the new compatibility that i found:
https://www.cisco.com/c/en/us/products/collateral/routers/2800-series-integrated-services-routers-isr/product_data_sheet0900aecd80581fe6.html

faruqfarkhan_0-1696317301193.png

Regard,

Can you paste the boot up process?

BR

****Kindly rate all useful posts*****

Hi daniel,

Here i paste the boot up process

System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2012 by cisco Systems, Inc.

Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
CISCO2901/K9 platform with 524288 Kbytes of main memory
Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC enabled


Readonly ROMMON initialized
program load complete, entry point: 0x80803000, size: 0x1b340


IOS Image Load Test
___________________
Digitally Signed Release Software
program load complete, entry point: 0x81000000, size: 0x3bd79fc
Self decompressing the image : ################################################# ################################################################################ ################################################################################ ################################################################################ ################################################################################ [OK]

Smart Init is enabled
smart init is sizing iomem
TYPE MEMORY_REQ
HWIC Slot 1 0x00200000
HWIC Slot 2 0x00200000
PVDM 0 0x00200000
Onboard devices &
buffer pools 0x0228F000
-----------------------------------------------
TOTAL: 0x0288F000

Rounded IOMEM up to: 44Mb.
Using 8 percent iomem. [44Mb/512Mb]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

 

Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M9, REL EASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Wed 12-Sep-12 03:31 by prod_rel_team
Image text-base: 0x2100D9D8, data-base: 0x25963100


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco CISCO2901/K9 (revision 1.0) with 479232K/45056K bytes of memory.
Processor board ID FGL183620QF
2 Gigabit Ethernet interfaces
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)


Press RETURN to get started!


Jan 2 12:00:03.231: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = c2900 Next reboot level = ipbasek9 and License = ipbasek9
Jan 2 12:00:03.395: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = c2900 Next reboot level = uck9 and License = uck9
Jan 2 12:00:03.543: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = c2900 Next reboot level = datak9 and License = datak9
Oct 3 04:36:34.375: %PVDM-6-UNSUPPORTED: Codec G.723 is not supported on PVDM3.
Oct 3 04:36:43.879: %ESWMRVL_FLTMG-5-NOTICE: Notice: FPGA Rev 0x27

Oct 3 04:36:43.883: fe_mrvl_hw_init : Could not load driver

Oct 3 04:36:43.883: %ESWMRVL_FLTMG-7-INTERNAL_ERR: Internal error: Unable to in tialize the Marvell switch for FE
, -Traceback= 0x21200014z 0x213FBCF4z 0x213FCFD4z 0x213D925Cz 0x21138714z 0x213 DC548z 0x2344CE2Cz 0x2344CF14z 0x222750B8z 0x22275358z 0x233ECA14z 0x233EC9F8zhw ic_fe_analyze_interface: Couldn't initialize the HWIC FE

Oct 3 04:36:45.107: %ESWMRVL_FLTMG-5-NOTICE: Notice: FPGA Rev 0x27

Oct 3 04:36:45.107: fe_mrvl_hw_init : Could not load driver

Oct 3 04:36:45.107: %ESWMRVL_FLTMG-7-INTERNAL_ERR: Internal error: Unable to in tialize the Marvell switch for FE
, -Traceback= 0x21200014z 0x213FBCF4z 0x213FCFD4z 0x213D925Cz 0x21138714z 0x213 DC548z 0x2344CE2Cz 0x2344CF14z 0x222750B8z 0x22275358z 0x233ECA14z 0x233EC9F8zhw ic_fe_analyze_interface: Couldn't initialize the HWIC FE

Oct 3 04:36:48.547: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
Oct 3 04:36:48.547: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down
Oct 3 04:36:48.547: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
Oct 3 04:36:49.743: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthe rnet0/0, changed state to down
Oct 3 04:36:49.743: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthe rnet0/1, changed state to down
Oct 3 04:36:51.631: %SYS-5-CONFIG_I: Configured from memory by console
Oct 3 04:36:52.799: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed stat e to administratively down
Oct 3 04:36:54.735: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M9, REL EASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Wed 12-Sep-12 03:31 by prod_rel_team
Oct 3 04:36:54.739: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
Oct 3 04:37:06.083: %DSPRM-5-UPDOWN: DSP 1 in slot 0, changed state to up
Router>show ip int br
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 192.168.0.1 YES NVRAM down down
GigabitEthernet0/1 unassigned YES NVRAM administratively down down
Router>show inven



Regards,

Review Cisco Networking for a $25 gift card