cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
931
Views
0
Helpful
0
Replies

TestLoopback failed on ports

rafaelsouza1
Level 1
Level 1

Hello,

 

I'm trying to configure two Catalyst 6500e in VSS mode. In the switch 2, I have a module SFP WS-F6700-DFC3CXL.

 

This module is presentig the following logs:

 

%CONST_DIAG-SW2_SPSTBY-3-BOOTUP_TEST_FAIL: Switch 2 Module 8: TestLoopback failed on port(s) 13-24

 

%DIAG-SW2_SPSTBY-3-MINOR: Switch 2 Module 8: Online Diagnostics detected a Minor Error. Please use 'show diagnostic result <target>' to see test results.

 

The ports from 13 to 24 is on error disable state:

 

%PM-SW2_SPSTBY-4-ERR_DISABLE: diagnostics error detected on Gi2/8/13, putting Gi2/8/13 in err-disable state

 

In show diagnostic, the output is

 

Current bootup diagnostic level: minimal

Switch 2 Module 8: CEF720 24 port 1000mb SFP  SerialNo : SAL1408BRLM

  Overall Diagnostic Result for Switch 2 Module 8 : MINOR ERROR
  Diagnostic level at card bootup: minimal

  Test results: (. = Pass, F = Fail, U = Untested)

    1) TestTransceiverIntegrity:

   Port  1  2  3  4  5  6  7  8  9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
   ----------------------------------------------------------------------------
         .  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U


    2) TestLoopback:

   Port  1  2  3  4  5  6  7  8  9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
   ----------------------------------------------------------------------------
         .  .  .  .  .  .  .  .  .  .  .  .  F  F  F  F  F  F  F  F  F  F  F  F


    3) TestTxPathMonitoring ------------> .
    4) TestSynchedFabChannel -----------> .
    5) TestL3VlanMet -------------------> .
    6) TestIngressSpan -----------------> .
    7) TestEgressSpan ------------------> .
    8) TestAsicMemory ------------------> U
    9) TestEobcStressPing --------------> U
   10) TestFirmwareDiagStatus ----------> .
   11) TestAsicSync --------------------> .
   12) TestUnusedPortLoopback:

   Port  1  2  3  4  5  6  7  8  9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
   ----------------------------------------------------------------------------
         U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U


   13) TestOBFL ------------------------> .
   14) TestErrorCounterMonitor ---------> .
   15) TestPortTxMonitoring:

   Port  1  2  3  4  5  6  7  8  9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
   ----------------------------------------------------------------------------
         .  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U  U


   16) TestLtlFpoeMemoryConsistency ----> .
   17) TestRwEngineOverSubscription ----> U

 

I don't know what is causing this problem. Does anyone have any tips?

0 Replies 0
Review Cisco Networking products for a $25 gift card