the system is unable to boot automatically. the boot environment variable needs to be set to a bootable image
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-26-2016 10:58 PM - edited 03-08-2019 06:47 AM
our switch is not working . kindly find the below error message.
the system is unable to boot automatically. the boot environment variable needs to be set to a bootable image
- Labels:
-
Other Switching
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-26-2016 11:12 PM
the system is unable to boot automatically. the boot environment variable needs to be set to a bootable image
Console into the appliance and reboot. Post the entire boot up process.
And what is the exact model of this appliance?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-26-2016 11:35 PM
the sw model is : WS-C3560-24TS-S...
the error message is : the system is unable to boot automatically. the boot environment variable needs to be set to a bootable image
i think flash is missing : flash:c3560-ipbase-mz.122-35.SE5/c3560-ipbase-mz.122-35.SE5.bin
its showing below
switch:
switch:
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-27-2016 12:05 AM
Abdul,
Console into the appliance, reboot & post the entire boot up process.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-27-2016 12:51 AM
we have reboot the same but the switch goes through the below mode
switch:
switch:
switch:
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-27-2016 12:53 AM
i will share my "" ammy admin "' ID address. could you please connect and check.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-27-2016 01:32 AM
leo,
Device is not booting up.
Can you please share me how to Upload new firmware into the switch.I have a valid firmware..
Kindly reply
please find attached
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-28-2016 05:21 AM
Device is not booting up.
Abdul,
I've made three (3) simple request and I sense the lack of seriousness from you, therefore, I hereby excuse myself from providing further assistance.
You are on your own.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-28-2016 09:00 PM
Good morning Leo,
Issue has been resolved through Youtube, please watch this video.
https://www.youtube.com/watch?v=zxTO5qxti-I
thanks for your support. have a nice day.
Regards,
Haroon.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-27-2016 01:04 AM
we have reboot the same but the switch goes through the below mode
switch:
switch:
switch:
Abdul,
3rd Request: Console into the appliance, reboot & post the entire boot up process.
Otherwise, I am going to presume you're not serious about this so I'll refrain from providing further assistance.
i will share my "" ammy admin "' ID address. could you please connect and check.
Unacceptable.
