Troubles with service Module

[jperezT3ms4]

Hello Team,

I have some troubles with some ISR's 2911.

1.- SM-ES2-24-P: EtherSwitch SM L2 + PoE + 23 10/100 + 1 10/100/1000 on Slot 1

2.- CISCO2911/K9 chassis

a) when I try to log in via telnet to the device does not respond, but if I send a ping this responds smoothly

b) The problem is that when I see the device restarts

when ocurrs the reboot on the device always sent this log:

Oct 29 14:23:47.251: %SYS-5-CONFIG_I: Configured from memory by console
Oct 29 14:23:47.527: %LINEPROTO-5-UPDOWN: Line protocol on Interface EDSP0, changed state to up
Oct 29 14:23:47.875: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Oct 29 14:23:49.451: %LINK-3-UPDOWN: Interface GigabitEthernet1/1, changed state to up
Oct 29 14:23:49.515: %ILPM_FAULT-5-ILPM_NOTICE: Notice: Inline power supply is being started.
Oct 29 14:23:49.515: %ILPM_FAULT-5-ILPM_WARNING: Warning: Ethernet Switch Network Modules with PoE Support need to be reloaded to function properly.
Oct 29 14:23:50.451: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to up
Oct 29 14:23:51.063: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 14-Jun-11 19:25 by prod_rel_team
Oct 29 14:23:51.067: %SNMP-5-COLDSTART: SNMP agent on host client is undergoing a cold start

someone had this same problem!!!

Help

[InayathUlla Sharieff]

this warning message is not a indication of any ERROR in the system
but a WARNING upon system reload or PoE power supply restoration. This is a
new PoE power supply OIR feature. Upon PoE OIR, inline power supply restores
automatically in the router but Ether Switch Network module requires to be
reloaded for PoE supply to work properly in the Ethernet switch .

HTH

[danjone3]

As Insharie noted, the posted messages have nothing to do with the inability to telnet to the device.  Are you trying and failing to telnet to the router or the etherswitch?  What configuration, if any, do you have on the vty lines of the device?
 

[dsobrinho]

Hi ,

I have same problem but the ip phones connect in sw module is not working becouse absent of POE.

I have already reload the module and the gateway nothing work.

ACMEGW_GW01#show power inline
PowerSupply   SlotNum.   Maximum   Allocated       Status
-----------   --------   -------   ---------       ------
INT-PS           0       280.000     0.000         PS GOOD   RPS ABSENT
Interface   Config   Device   Powered    PowerAllocated
---------   ------   ------   -------    --------------
Gi1/0       auto     Unknown  Off        0.000 Watts

Ethernet Switch Network Modules with PoE support should be reloaded to function
 properly upon PoE Power Supply OIR insertion/removal.



NME-16ES-1G-P


*Nov 18 14:25:38.207 GMT-2: %ILPM_FAULT-5-ILPM_NOTICE: Notice: Inline power supp
ly is being started.
*Nov 18 14:25:38.207 GMT-2: %ILPM_FAULT-5-ILPM_WARNING: Warning: Ethernet Switch
 Network Modules with PoE Support need to be reloaded to function properly.
*Nov 18 14:25:40.035 GMT-2: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.4(3)M4, REL
EASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Sun 27-Sep-15 06:34 by prod_rel_team