10-08-2014 01:37 PM - edited 03-07-2019 09:02 PM
Bear with me as this is my first install of a 6500 and WiSM module.
The backgroud is that we are small, but management used to be in networking and basically forced the the purchase of a 6509E. Most of my experience is with 3560X and 2950 switches.
I have followed the basic deployment guide here:http://www.cisco.com/c/en/us/support/docs/interfaces-modules/catalyst-6500-series-7600-series-wireless-services-module-wism/112968-wism2-deploy-guide-00.html. My problem is that I have a flat network (see why I didn't want a 6500) so the management network and the production network is on VLAN 1. Yes I know how bad this is, but apparently wireless is more important than adhering to good security practices.
My problem is I am unable to access the Web UI of the controller. I am however able to ping the address for the management IP. I will give as much output as I can think would be helpful right now (and more if needed), but any assistance I can get would be appreciated.
#show module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 4 WiSM 2 WLAN Service Module WS-SVC-WISM2-K9 SAL172579DM
6 5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G SAL1706YCQJ
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
2 30f7.0d0b.9820 to 30f7.0d0b.982f 1.1 12.2(18r)S1 15.1(1)SY1 Ok
6 ccef.4838.97d5 to ccef.4838.97dc 1.4 12.2(50r)SYS 15.1(1)SY1 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
6 Policy Feature Card 4 VS-F6K-PFC4 SAL17299W2L 2.1 Ok
6 CPU Daughterboard VS-F6K-MSFC5 SAL1706YBTQ 1.5 Ok
Mod Online Diag Status
---- -------------------
2 Pass
6 Pass
#sh wism module 2 controller 1 st
WiSM Controller 1 in Slot 2 configured with auto-lag
Operational Status of the Controller : Oper-Up
Service VLAN : 50
Service Port : 3
Service Port Mac Address : 6c20.562c.2c61
Service IP Address : 192.168.2.51
Management IP Address : 40.96.0.2
Software Version : 7.0.116.0
Port Channel Number : 403
Allowed-vlan list : 1
Native VLAN ID : 1
WCP Keep Alive Missed : 0
#do sh wism st
Service Vlan : 50, Service IP Subnet : 192.168.2.1/255.255.254.0
WLAN
Slot Controller Service IP Management IP SW Version Controller Type Status
----+-----------+----------------+----------------+------------+------------------+---------------
2 1 192.168.2.51 40.96.0.2 7.0.116.0 WS-SVC-WISM-2-K9 Oper-Up
HQR1#sh ip int brief
Interface IP-Address OK? Method Status Protocol
TenGigabitEthernet2/1 unassigned YES unset up up
TenGigabitEthernet2/2 unassigned YES unset down down
GigabitEthernet2/3 unassigned YES unset up up
GigabitEthernet2/4 unassigned YES unset administratively down down
GigabitEthernet6/1 unassigned YES unset up up
GigabitEthernet6/2 unassigned YES unset down down
GigabitEthernet6/3 unassigned YES unset down down
TenGigabitEthernet6/4 unassigned YES NVRAM administratively down down
TenGigabitEthernet6/5 unassigned YES NVRAM administratively down down
Port-channel403 unassigned YES unset up up
Vlan1 40.96.0.1 YES NVRAM up up
Vlan50 192.168.2.1 YES NVRAM up up
Solved! Go to Solution.
10-08-2014 02:41 PM
Can you telnet/SSH into the WiSM2 card?
Can you session into the WiSM2 card? Command: session slot 2 proc 1
10-08-2014 02:41 PM
Can you telnet/SSH into the WiSM2 card?
Can you session into the WiSM2 card? Command: session slot 2 proc 1
10-08-2014 03:01 PM
Yes I can ssh and session to the card.
10-08-2014 04:36 PM
Well I feel stupid, apparrently, either by default or by my commands "Web mode" and Secure Web Mode" was disabled. after enabling, it works.
10-08-2014 07:54 PM
Glad to hear you've fixed the issue.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide