04-09-2012 08:13 AM - edited 03-17-2019 11:01 PM
Hello Everyone,
I was wondering if someone would be able to help us solve this we are having while trying to connect our AS5400 with Avaya PBX. We have been able to bring up the PRI Between the two devices ( When i try the following command "show isdn status" I do see the multiframe established) but when I receive a call from the AVAYA PGX i see the following error message on debug. What we are trying to accomplish is sending the call from one our site in NA over the WAN to our site in India. I'm pretty new with Voice and any help would be greatly appreciated.
Apr 5 18:35:08.267: 00010189--0000008B
*Apr 5 18:35:08.267: ISDN Q921d: isdn_l2d_srq_process: event_count 1
*Apr 5 18:35:08.267: ISDN L2_CODE: isdn_l2_process: state (0x0), event_count (
1)
*Apr 5 18:35:36.415: ISDN Se7/0:23 **ERROR**: call_incoming: Received a call id
0xDD with a bad bearercap from <unknown> on b channel 23
*Apr 5 18:35:36.415: ISDN Se7/0:23 CCd: CC_CHAN_GetUserpri: using call_id = 0xD
D
*Apr 5 18:35:36.415: ISDN Se7/0:23 CCd: CC_CHAN_ReleaseChanpri: channel 23
fh-bcr-t1-gw#
Here a copy the running config on the AS5400
ip cef
!
!
isdn switch-type primary-4ess
!
!
voice service voip
signaling forward unconditional
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback none
h323
sip
bind control source-interface FastEthernet0/1
bind media source-interface FastEthernet0/1
call service stop
!
!
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8
controller T1 7/0
framing esf
linecode b8zs
pri-group timeslots 1-24
!
controller T1 7/1
framing esf
linecode b8zs
!
controller T1 7/2
framing sf
linecode ami
!
controller T1 7/3
framing sf
linecode ami
!
controller T1 7/4
framing sf
linecode ami
!
controller T1 7/5
framing sf
linecode ami
!
controller T1 7/6
framing sf
linecode ami
!
controller T1 7/7
framing sf
linecode ami
!
!
!
interface FastEthernet0/0
no ip address
shutdown
duplex auto
speed auto
!
interface FastEthernet0/1
ip address 10.12.10.15 255.255.255.0
duplex auto
speed auto
!
interface Serial0/0
no ip address
shutdown
clock rate 2000000
!
interface Serial7/0
no ip address
!
interface Serial0/1
no ip address
shutdown
clock rate 2000000
!
interface Serial7/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-4ess
isdn timer T310 40000
isdn protocol-emulate network
isdn supp-service name calling
no cdp enable
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 10.12.10.1
!
no ip http server
!
!
!
!
!
!
control-plane
!
!
!
voice-port 7/0:D
!
!
!
dial-peer voice 117672 voip
destination-pattern 117672
session target ipv4:10.12.7.24
dtmf-relay rtp-nte
!
!
ss7 mtp2-variant Bellcore 0
ss7 mtp2-variant Bellcore 1
ss7 mtp2-variant Bellcore 2
ss7 mtp2-variant Bellcore 3
!
line con 0
line aux 0
line vty 0 4
login local
line vty 5 105
login local
line 2/00 3/107
modem InOut
!
end
04-09-2012 09:53 AM
try command as per this support page as it seems its taking as data call
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide