All:
Per my previous thread, has anyone used NM-CUE (or NME-CUE) with an SM-NM-ADPTR on ISR G2?
I'm attemping a TFTP BootLoader recovery.
I've recovered AIM-CUE dozens of times on Cisco UC500/UC520, but this is the first time with NM-CUE.
Once I instruct the NM-CUE to boot from TFTP, the boot fails, and I'm kicked off the serial console of the NM-CUE when the IOS's interface goes physically down (EmbeddedServiceEngine0/0 interface)
I've tried two different NM-CUEs at this point, I'm not certain if the NM-CUE itself is even powering up and being detected.
1) Neither the NME-CUE or the SM-NM-ADPTR shoes up in 'sh inventory'; but they boot up and I'm able to console in?
2) The 80 GB SATA disk onboard doesn't show up in the boot loader. Only a 256 USB/Flash device is shown.
Again, no experience with this hardware.
Looking for a clue.
~BAS
----------
br0.northhills# sh run int embedded-Service-Engine 0/0
!
interface Embedded-Service-Engine0/0
ip address 10.108.11.129 255.255.255.248
ip nat inside
ip virtual-reassembly in
service-module ip address 10.108.11.130 255.255.255.248
service-module enable
no keepalive
end
br0.northhills# service-module embedded-Service-Engine 0/0 reset
Use reset only to recover from shutdown or failed state
Warning: May lose data on the the NVRAM, nonvolatile file system or unsaved configuration!
Do you want to reset?[confirm]
Trying to reload Service Module Embedded-Service-Engine0/0.
br0.northhills# service-module embedded-Service-Engine 0/0 session
boot-loader > verify
** Bad Reisefs partition or disk - ide 0:1 **
[...reset again ...]
U-Boot 1.1.1 (Development build) (Build time: Nov 1 2010 - 15:49:00)
Using default environment
Allocated 10000000 bytes at 0xa800000080000000 for 2nd core
Net: icceth0
Bus 0 (CF Card): OK
ide 0:Model: UGB30STX0256Z6-FAA-2PC Firm: 100511g
Ser#: UNIGEN4 00407162
Type: Hard Disk
Capacity: 249.5 MB = 0.2 GB (510976 x 512)
Sending link up to other core .................. done ---> 0
Waiting for link up from other core ..................
......LINK is UP
SRE: Sending Registration...
Setting up RBIP communication
SRE: No Installation Needed
Please enter '***' to change boot configuration: ***
ServicesEngine Bootloader Version : 1.0
Using icceth0 device
TFTP from server 192.168.137.1; our IP address is 10.108.11.130; sending through gateway 10.108.11.129
Filename 'cue-installer.nmx.8.6.7'.
Load address: 0x25000000
Loading: #################################################################
#################################################################
#################################################################
####
done
Bytes transferred = 10182012 (9b5d7c hex), 1158 Kbytes/sec
[ ...delay ... ]
000139: Sep 21 01:17:32.237 EDT: %LINK-3-UPDOWN: Interface Embedded-Service-Engine0/0, changed state to down
000140: Sep 21 01:17:33.237 EDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface Embedded-Service-Engine0/0, changed state to down
~BAS
--------------
Hardware: Cisco 2921 + SM-NM-ADPTR + NME-CUE (See sh inventory, PNGs attached)
IOS Version: Version 15.5(3)M6, REL EASE SOFTWARE (fc2)
CUE Version: cue-installer.nmx.8.6.7
-------------
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.5(3)M6, REL EASE SOFTWARE (fc2)
Installed image archive
Cisco CISCO2921/K9 (revision 1.0) with 2244608K/114688K bytes of memory.
Processor board ID FTX1902AJMB
5 Gigabit Ethernet interfaces
2 terminal lines
1 Virtual Private Network (VPN) Module
4 Voice FXO interfaces
2 Voice FXS interfaces
2 Voice E & M interfaces
1 cisco Embedded service engine(s)
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
4001760K bytes of ATA System CompactFlash 0 (Read/Write)
br0.northhills# sh inventory
NAME: "CISCO2921/K9", DESCR: "CISCO2921/K9 chassis, Hw Serial#: FTX1902AJMB, Hw Revision: 1.0"
PID: CISCO2921/K9 , VID: V08 , SN: FTX1902AJMB
NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSlot 0", DESCR: "2nd generation four port FXO voice interface daughtercard"
PID: VIC2-4FXO , VID: V03 , SN: FOC13190LUH
NAME: "3rd generation two port FXS DID voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "3rd generation two port FXS DID voice interface daughtercard"
PID: VIC3-2FXS/DID , VID: V03 , SN: FOC15175C6Q
NAME: "3rd generation two port EM voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "3rd generation two port EM voice interface daughtercard"
PID: VIC3-2E/M , VID: V01 , SN: FOC14202P6K
NAME: "PVDM3 DSP DIMM with 64 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 64 Channels"
PID: PVDM3-64 , VID: V01 , SN: FOC16055U6P
NAME: "1000BASE-SX SFP", DESCR: "1000BASE-SX SFP"
PID: GLC-SX-MMD , VID: B2 , SN: SCH37348000
NAME: "SM-ES3G-24-P: EtherSwitch SM L3 + POE + 24 10/100/1000 on Slot 1", DESCR: "SM-ES3G-24-P: EtherSwitch SM L3 + POE + 24 10/100/1000"
PID: SM-ES3G-24-P , VID: V01 , SN: FOC14203SPM
NAME: "C2921/C2951 AC-POE Power Supply", DESCR: "C2921/C2951 AC-POE Power Supply"
PID: PWR-2921-51-POE , VID: V02 , SN: QCS1530F0S8
br0.northhills# service-module Embedded-Service-Engine 0/0 status
Service Module is Cisco Embedded-Service-Engine0/0
Service Module supports session via TTY line 2
Service Module heartbeat-reset is enabled
Embedded Service Engine boot state is UBOOT UP
Module resource information:
CPU Frequency: 500 MHz
Memory Size: 256 MB
Disk Size: 249 MB
No install/uninstall in progress
