12-19-2013 02:01 AM - edited 03-19-2019 07:40 AM
We having SIP intregration CUCM and CUC ,We have two CUC server in HA mode(active/Active).
When the two servers is UP then MWI will working properly ,When any one of CUC is down MWI is not working
12-19-2013 03:36 AM
Hi Nishad
Which version of CUC are you running
Please let me kno
Regards
Carlo
Please rate all helpful posts
"The more you help the more you learn"
12-19-2013 03:57 AM
Current Version 9.1.2-10000-28
12-19-2013 04:33 AM
Hello Nishad,
1.Do you see the dialout being attempted in the Port Status Monitor ?
2.Have you checked the Conversation Manager and the Notifier traces ?
3. For the tested use do you see the status as on in User>Edit>Message Waiting Indicator even though the light does not come up on the phone?
4.Do you have SIB (Unified Messaging)?
5.If you change manually the Primary role on the nodes can the issue be reproduced?
-Regards
D%R%P
12-19-2013 05:01 AM
Thanks david for your reply..
We didnt get the chance to collect the Trace and Port Status monitor
When we were checking the User>Edit>MWI ---it was showing Off only even the user had a new Message
We are not using SIB , We are getting the issue only when any one of the server is down
12-19-2013 05:22 AM
Nishad,
Enable the following Traces. Go to Cisco Unity Connection Serviceability> Trace> Macro Traces:
-Call Flow Diagnostics (All)
-Call Control Miu Traces (All)
-Conversation Traces (All)
Now go to Trace>Micro Traces
-Notifier (All except Level 00 and 01)
Reproduce the issue, gather traces and post time stamp, extension and alias of the test user, to check on the CUC perspective.
-Regards
D%R%P
01-08-2014 06:05 AM
Hi David,
I have reproduced the issue ,Attached the Trace in the main post and details of the trace
Regards,
Nishad KI
01-08-2014 11:07 AM
Hi,
Please check that you have some ports on the sub server available for "send MWI requests". One of the lines in the "diag_CuNotifier-00000002.uc jumped out to me:
Error=No MWI ports on switchrecv=1389188137
If that's not it, please verify that the phones can actually call the MWI on/off number assigned to the sub.
Just a couple of thoughts that might help (or not!)
Gareth
01-08-2014 11:21 AM
Hello NIshad K I,
From the CUC traces here is a snippet:
19:05:37.954 |23517,,,Notifier,12,test user2: MWI (ON) failed. Details=Failed MWI [user='test user2' extension='8289' type=MWI_ON mwiType=0=Port phoneSystem=SIP2 (fb470cb1-de09-42b5-aacb-7967e37f6526)] Error=No MWI ports on switch
Three things to check:
1- Make sure your user is assigned with the correct phone system:
2-Make sure that you have ports with the "Send MWI Requests" enabled:
3-Last but not least make sure that the CUCM server order in the CUC port group matches the CM group of the device pool that the Trunk is using.
Regards,
D%R%P
01-09-2014 05:38 AM
David ..Thanks for your mail...
Really appriciate your response ....
What is the point of the same order of CUCM group in the CUC and CUCM group in the Device pool ?
We can add more servers in the CUC port group ,But in the CUCM group only three servers only possible ..
So how it will work ?
08-11-2014 02:40 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide