About AlexBar76

AlexBar76 · 05-04-2022

Hi I'm in trouble with this simple config I had two sites connected via customer LAN in L2, in those sites i had two cisco 1921 configured in HSRP the default gw for the network is the vip 10.240.0.254 see the attached schema and config the HSRP work...

AlexBar76 · 01-21-2022

I can authenticate through anyconnect and grab the ip address that I set in the vpn pool but I cannot ping any internal host, only the asa ip reply Internal is 10.0.145.0 VPN network is 10.1.47.0 No errors in the log Here the ASA config ASA Vers...

AlexBar76 · 01-19-2022

Hi All,I've been configure an L2TP connection on a cisco router cp 1111-8p ios-xe with this parameters vpdn enable vpdn-group 1 ! Default L2TP VPDN group accept-dialin protocol l2tp virtual-template 1 no l2tp tunnel authentication interface Virtu...

AlexBar76 · 05-28-2021

Goodmorning I'm try to set up a dynamic VPN between two router Cisco The main router is connected to a static Internet IP ADDRESS and the remote Router Use a Sla Monitor and Track to choose the alternate way via VPN use a crypto IPSEC vpn via 4g Gat...

AlexBar76 · 05-04-2021

Hi I'm try to assign a license to my cisco CP-1111 router via smart licenseI have insert the token and if i do sh license status It say registered but do not take from the virtual account the Security License I have 10 up 10 unassigned The router go...

AlexBar76 · 05-05-2022

Thanks to all for the support, I've solve the problem modify the conf, remove the hsrp configuration and re-insert It again in both routersand now it's works

AlexBar76 · 05-04-2022

Why ? It's a normal site with two router in the same Subnet as also CISCO show in HSRP docs i have also other sites in the same way and they works

AlexBar76 · 05-04-2022

Site A it's the right one I can attach the HSRP config here and the debug HSRP output SITE Ainterface GigabitEthernet0/0description $ETH-LAN$ip address 10.240.0.253 255.255.255.0standby 150 ip 10.240.0.254standby 150 priority 105standby 150 preemptst...

AlexBar76 · 05-04-2022

I see the virtual MAC filled on ARP table of the switches and goes trougth the networki have two different geographic sites connected via layer2 this L2 connection is between the two routers in the ge0/0 interface

AlexBar76 · 01-24-2022

Thank I've fix the problem for some reason many w10 client with l2tp vpn configured do not use l2tp port 1700 but try to use the 500 that is for the ipsec also if no ipsec are configured in the vpn clientso you need to modify the windows registry an...

Member Since	‎02-17-2021 11:22 PM
Date Last Visited	‎10-26-2022 12:03 AM
Posts	28
Total Helpful Votes Received	5

User Statistics

User Activity

HSRP CISCO 1921 ICMP Problems

Anyconnect client ping asa but not ping internal network

L2TP don't work in some Windows10 Client and in other yes

Crypto IPSEC do NOT START

SMART LICENSE PROBLEM

Re: HSRP CISCO 1921 ICMP Problems

Re: HSRP CISCO 1921 ICMP Problems

Re: HSRP CISCO 1921 ICMP Problems

Re: HSRP CISCO 1921 ICMP Problems

Re: L2TP don't work in some Windows10 Client and in other yes