About jrmalmeida

jrmalmeida · 11-19-2013

Hi,I need to configure a new VIP so that if the requests come on port 80 it sends a redirection message to clients saying to try on port HTTPS://*:9443, is the configuration below correct?rserver host server1 description host1 ip address 1.1.1.1 p...

jrmalmeida · 12-07-2011

Hi all!I am setting up a Cisco MARS version 6.1.3 (3501). And I'm having trouble saving reports. I need saving the incidents in workstation. I need that the Mars generate a file with informations of incident, for example: Session/Incident ID, Event T...

jrmalmeida · 06-08-2011

Hi Guys! I need configure management port of the 4500 Catalyst for CNA (Cisco Network Assistant) software access. My switch have this configuration: interface FastEthernet1ip vrf forwarding mgmtVrfip address 172.16.4.250 255.255.248.0speed autoduplex...

jrmalmeida · 01-14-2011

Hi all!We are using IP SLA to monitor the WAN IP from a client:ip sla monitor 1type echo protocol ipIcmpEcho 192.168.251.206 source-interface GigabitEthernet0/1request-data-size 10timeout 2000threshold 4000frequency 5ip sla monitor schedule 1 life fo...

jrmalmeida · 06-03-2010

Hi all!How do I check the status of the license of the ACS appliance version 4.2?Appreciate any help.Thank´s.

jrmalmeida · 08-26-2015

Dear Mohamed,I'm having the same problem with 1042n.Did you fix it ?I found some similar issue here in the forum and for some of them the resolution was to set radio preamble to long (no preamble-short). I did not try it yet. Thanks and best regardsJ...

jrmalmeida · 02-09-2012

Hi Keith! Thanks for information. I generate the incidents starting from a query. Generating one CSV file: http://www.cisco.com/en/US/docs/security/security_management/cs-mars/6.0/user/guide/combo/q_report.html#wp682776In this CSV file does not have...

jrmalmeida · 06-09-2011

Hi all! I seen that management interface, not support HTTP and HTTPS (CNA use HTTP and HTTPS). http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/53SG/configuration/sw_int.html#wp1119456Thanks for help!

jrmalmeida · 06-09-2011

Hi edwin! Yeah, the interface FastEthernet1 is up/up: PA10#ping 172.16.4.250Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 172.16.4.250, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 msC4...

jrmalmeida · 01-14-2011

Hi Sachin! I think it would be interesting to increase the monitoring time, if the main link becomes down. You know I can how do this without using load balancing (HSRP, VRRP, GLBP ...)? Because we are monitoring the wan interface of the client, ie...

Member Since	‎12-19-2008 10:44 AM
Date Last Visited	‎04-03-2018 02:32 PM
Posts	54
Total Helpful Votes Received	5

User Statistics

User Activity

ACE port redirection message to client

Generate Reports - Saving workstation

Configuring CNA in 4500 Catalyst - Management port - SUP6L-E

IP SLA Monitor

Ckeck Status License in ACS 4.2

Dear Mohamed,I'm having the

Generate Reports - Saving workstation

Re: Configuring CNA in 4500 Catalyst - Management port - SUP6L-E

Re: Configuring CNA in 4500 Catalyst - Management port - SUP6L-E

Re: IP SLA Monitor