About Chamindaw_2

Chamindaw_2 · 05-25-2011

Hi All,I'm just trying to analyse ICMP path echo between two Cisco devices which are 4 hops apart from ech other.Here is my configuration.ip sla monitor 150 type pathEcho protocol ipIcmpEcho 192.168.128.12 source-ipaddr 192.168.133.253 verify-data fr...

Chamindaw_2 · 03-24-2011

Hi All,I've been trying to change the STP mode of my MPLS aggrigation switches to MST due to many reasons but without success. (Currently all switches are working on PVST+.)Below given my sample network topology, configurations on both switches and ...

Chamindaw_2 · 03-01-2011

HI All,We are using Cisco ME-C3750-24-TE (c3750me-i5-mz.122-25.SEG1) switches in our MPLS aggrigation layer. Now it has reached to 1005 VLAN configurations and do not allow to create new VLANs.XXXXXXXX-SW1#sh vlan summary Number of existing VLANs ...

Chamindaw_2 · 09-07-2010

Hi All,I have been experiencing a difficulty in configuring a L2 bridging/local connect on a SPA-2X1GE-V2 card in a 7600-SIP-400. [12.2(33) SRD]Pl refer the attached solution diagram.(MPLS Local Connect.jpg)My requirement is to provide a L2 connectio...

Chamindaw_2 · 07-01-2010

Hi all,I have a requirement to apply an ACL on around 100 interfaces to block sertain ports (UDP&TCP) due to government regulation requirements. I've a 7609 router with SUP720-3BXL superwisor engine (act as a MPLS PE in our netrowk) with average CPU ...

Chamindaw_2 · 06-05-2011

Hi Fabrizio,'sh ip sla monitor stat aggregated detail' command works with 12.4T train and lator IOS codes only. I setup a lab and tested it.This command gives hop-by-hop detals as I was looking for.Thank You very juch for your time and support exte...

Chamindaw_2 · 06-01-2011

Hi Fabrizio,Many thanks for your continuous support.I removed configurations related to IP SLA 150 since there was a firewall blocking inbetween the path and configured IP SLA 300 instead.It seems IP SLA 300 probe is working fine. In my router I'm us...

Chamindaw_2 · 06-01-2011

Hi Fabrizio,Thanks for your reply. As you said I also noticed same and I did another testing with separate probe.Below given the full details.Here is my test setup, configurations and “show” outputs. Test setup; Router-1#sh versionCisco IOS Softwa...

Chamindaw_2 · 03-27-2011

Hi Laurant,Thanks for your reply.Actually my requirement is to have local MST reigions per MPLS PE. That is why I psecificaly block native VLAN passing through the PW and did not enable any L2 protocols via PW.( believe this is a good practice.. ;...

Chamindaw_2 · 03-27-2011

Hi Jon,Thanks for your reply. I'm having a practcal difiiculty of configuring port mode PW, since all my L2 & L3 customer connections interface with MPLS PE via same Gig port, further my requirement is to have local MST reigions per MPLS PE hence do ...

Member Since	‎07-01-2010 12:51 AM
Date Last Visited	‎08-18-2017 03:54 AM
Posts	17

User Statistics

User Activity

IP SLA path echo analysis

MST BPDU via EoMPLS Pseudowire Connections

ME 3750 Maximum supported VLANs

MPLS - Problem in Local Connect on Cisco 7609

CPU impact with ACLs

IP SLA path echo analysis

Re: IP SLA path echo analysis

Re: IP SLA path echo analysis

Re: MST BPDU via EoMPLS Pseudowire Connections

Re: MST BPDU via EoMPLS Pseudowire Connections