Hi,   Not sure if this is at all possible, but...   - Does CUBE HA / HSRP support the use of Layer 3 port channel on the CUBE router end? We are looking to make use of Nexus vPC capability by doing CUBE Layer 3 Portchannel > Nexus 7k Layer 2 vPC in access mode. [this is to account for individual link and core switch failure, without forcing CUBE failover]   The  HA documentation looks like it uses one link only per HSRP group.   http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-border-element/112095-cube-hsrp-config-00.html   Cheers, Rob   ... View more

Hi All, We are in the middle of replacing 2 x  old cat6k which are end of life soon with some new hardware/software. Current boxes are functioning as a collapsed core/distribution switch + router. Questions are: 1) Is there a one or some commands (NOT 'sh run') which will let me what services this cisco box is offering ( ie Layer2, Layer3, etc). I can work out from the image that its running what features the box can support, but I would actually like to know without looking at the configure what services it is providing. 2) What is the recommended upgrade box in the cat 6k family? 3) What are some alternative ( cisco ) boxes which could be the replacement ( nexus 5500, cat 4k, etc ) ? A brief summary the boxes we are replacing hardware/software wise: IOS (tm) s222_rp Software (s222_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(18)SXF16, RELEASE SOFTWARE (fc2) cisco WS-C6509 (R7000) processor (revision 2.0) with 458752K/65536K bytes of memory. Processor board ID XXXXXXXXXXXXXX R7000 CPU at 300Mhz, Implementation 0x27, Rev 3.3, 256KB L2, 1024KB L3 Cache Last reset from power-on SuperLAT software (copyright 1990 by Meridian Technology Corp). X.25 software, Version 3.0.0. Bridging software. TN3270 Emulation software. 16 Virtual Ethernet/IEEE 802.3 interfaces 48 FastEthernet/IEEE 802.3 interfaces 74 Gigabit Ethernet/IEEE 802.3 interfaces 381K bytes of non-volatile configuration memory. 32768K bytes of Flash internal SIMM (Sector size 512K). Configuration register is 0x2102 dcccore01#sh mod Mod Ports Card Type                              Model              Serial No. --- ----- -------------------------------------- ------------------ -----------   1    2  Catalyst 6000 supervisor 2 (Active)    WS-X6K-SUP2-2GE    XXXXXXXXXXX   2   16  SFM-capable 16 port 10/100/1000mb RJ45 WS-X6516-GE-TX     XXXXXXXXXXX   3    8  8 port 1000mb GBIC Enhanced QoS        WS-X6408A-GBIC     XXXXXXXXXXX   8   48  48 port 10/100/1000mb EtherModule      WS-X6148-GE-TX     XXXXXXXXXXX   9   48  48-port 10/100 mb RJ45                 WS-X6148-RJ-45     XXXXXXXXXXX Mod MAC addresses                       Hw    Fw           Sw           Status --- ---------------------------------- ------ ------------ ------------ -------   1  XXXXXXXXXXXXXX to XXXXXXXXXXXXXX   3.13  7.1(1)       12.2(18)SXF1 Ok   2  XXXXXXXXXXXXXX to XXXXXXXXXXXXXX   2.0   6.1(3)       8.5(0.46)RFW Ok   3  XXXXXXXXXXXXXX to XXXXXXXXXXXXXX   1.7   5.4(2)       8.5(0.46)RFW Ok   8  XXXXXXXXXXXXXX to XXXXXXXXXXXXXX   3.0   7.2(1)       8.5(0.46)RFW Ok   9  XXXXXXXXXXXXXX to XXXXXXXXXXXXXX   1.1   5.4(2)       8.5(0.46)RFW Ok Mod  Sub-Module                  Model              Serial       Hw     Status ---- --------------------------- ------------------ ----------- ------- -------   1  Policy Feature Card 2       WS-F6K-PFC2        XXXXXXXXXXX  3.3    Ok   1  Cat6k MSFC 2 daughterboard  WS-F6K-MSFC2       XXXXXXXXXXX  2.6    Ok ... View more

Hi All, We are currently working on providing network monitoring information of our server farms programmed on our ACE modules, what is the best OID's to use? ... View more