Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About dmifly.chuang
11-05-2018
dmifly.chuang
Member since
08-25-2011
Beginner
3
Posts
0
Helpful
0
Solutions
Created by
dmifly.chuang
in Firewalls
in Firewalls
01-21-2013
10:27 PM
01-21-2013
10:27 PM
It is ok now i follow your guide successful to setup dual isp on my asa but it seems could not access from the backup isp (have not direct a default route ) by asdm? it is common status? Or it should access from any interface which security-level = 0?
... View more
Created by
dmifly.chuang
in Firewalls
in Firewalls
01-21-2013
06:30 PM
01-21-2013
06:30 PM
i set up an asa in my business network , and i have internet service from two ISP now, i want to manage my asa from internet by ASDM could i use both the public ip address which i set up in asa outside interface to manage my asa? the default route on my asa is only direct to one isp thx for your help!
... View more
Labels:
12-13-2012
11:57 PM
I have a question,my test topology is like this. then,i have test what i want. i shutdown port-channel, both with two physical cable. and hsrp state was down, because there no broadcast domain to transfer hello packet And then,I was thinking, Is there a feature can let hsrp hello packet run in another link? such as link direct-connect between two router. thanks for your help.
... View more
Labels:
Created by
dmifly.chuang
in Service Providers Documents
in Service Providers Documents
04-03-2012
02:07 AM
04-03-2012
02:07 AM
i hace a module vwic2-1mft-e1/t1 i want to change the card type from t1 to e1 i could see card type e1 0 0 on my running-config but controller still is t1 and i could not enter "no controller t1 0 0" to remove controller of t1 i need help
... View more
Labels:
Created by
dmifly.chuang
in Networking Documents
in Networking Documents
08-25-2011
08:29 PM
08-25-2011
08:29 PM
R2: R2#sh ip eigrp topology EIGRP-IPv4 Topology Table for AS(1)/ID(192.168.5.1) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 192.168.4.0/24, 1 successors, FD is 281600 via Connected, Ethernet0/1 P 6.6.6.6/32, 1 successors, FD is 281600 via Rstatic (281600/0) P 192.168.5.0/24, 1 successors, FD is 281600 via Connected, Ethernet0/0 router eigrp 1 network 6.6.6.6 0.0.0.0 network 192.168.4.2 0.0.0.0 network 192.168.5.0 no auto-summary ip route 6.6.6.6 255.255.255.255 Ethernet0/0 R3: R3#sh ip eigrp topology EIGRP-IPv4 Topology Table for AS(1)/ID(192.168.4.1) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 192.168.4.0/24, 1 successors, FD is 281600 via Connected, Ethernet0/1 P 6.6.6.6/32, 1 successors, FD is 307200 via 192.168.4.2 (307200/281600), Ethernet0/1 P 192.168.5.0/24, 1 successors, FD is 307200 via 192.168.4.2 (307200/281600), Ethernet0/1
... View more
Created by
dmifly.chuang
in Networking Documents
in Networking Documents
08-25-2011
07:40 PM
08-25-2011
07:40 PM
i am testing routing protocol redistribute,now i have a question.R1,R2 and R3 is direct connection of eachother. eigrp running on R2 and R3 . R1 has a loopback interface.R2 need a loopback route,so i use ip route command. when i use ip route ip_address 0.0.0.0 next_hop_address and network at eigrp session in R2,i can not show up in R3. when i change form,i use ip route ip_address 0.0.0.0 interface_name.then R3's route table has this route. can somebody explain it for me?thanks you
... View more
Labels:
01-21-2013 10:27 PM
It is ok nowi follow your guide successful to setup dual isp on my
asabut it seems could not access ...
01-21-2013 06:30 PM
i set up an asa in my business network , and i have internet service
from two ISPnow, i want to mana...
12-13-2012 11:57 PM
I have a question,my test topology is like this.then,i have test what i
want.i shutdown port-channel...
Created by
dmifly.chuang
in Service Providers Documents
04-03-2012 02:07 AM
04-03-2012 02:07 AM
i hace a module vwic2-1mft-e1/t1i want to change the card type from t1
to e1i could see card type e1...
Created by
dmifly.chuang
in Networking Documents
08-25-2011 08:29 PM
08-25-2011 08:29 PM
R2:R2#sh ip eigrp topology EIGRP-IPv4 Topology Table for
AS(1)/ID(192.168.5.1)Codes: P - Passive, A ...
Created by
dmifly.chuang
in Networking Documents
08-25-2011 07:40 PM
08-25-2011 07:40 PM
i am testing routing protocol redistribute,now i have a question.R1,R2
and R3 is direct connection o...
Public Statistics
| Date Registered | 08-25-2011 07:32 PM |
| Date Last Visited | 11-05-2018 08:56 PM |
| Total Messages Posted | 3 |
