About kay.kang

kay.kang · 06-11-2024

I've set one switch as root primary for MST instance 0 and 1. (I see the switch has locally priority 0 for two instances) And set as root secondary for MST instance 2. (I see the switch has locally priority 4096 for the instance 2).When I checked the...

kay.kang · 06-04-2024

Hi,We're operating VPC between two N3K devices.And try to add a different VLAN to each VPC member switch(Nexus3000-A-1 and Nexus3000-A-2) as attached diagram.That additional VLAN is connecting through each ISP SW(ISP SW_1 & ISP SW_2).We're not plann...

kay.kang · 05-28-2024

Hi,We have a router(Router 2 in picture) receiving a default route received from RIP.And, we're planning to get new EBGP peering, which will receive another default route from the peer and the goal of the design is that we want to keep the RIP defaul...

kay.kang · 09-12-2023

Hi,We want to allow some ReadOnly users to do show running command with nexus switch but not allow them to still make any change configuration. It seems RO users can put some commands but they can't put show run command yet. Following snapshots are o...

kay.kang · 09-12-2023

Hi,We want to allow some ReadOnly users to do show running command across network device but not allow them to still make any change configuration. It seems RO users can put some commands but they can't put show run command yet. Following snapshots a...

kay.kang · 06-05-2024

Thanks for the response.From my lab test, N3K-A-1 showed VLAN 30 on Locally suspended VLANs and N3K-A-2 showed VLAN 40 on Locally suspended VLANs in the scenario. I just configured relevant SVI on each Nexus switch and tested ping to next hop IP over...

kay.kang · 06-04-2024

Thanks, Scott for the reply.I am thinking of a best practice to make this scenario work.Without any process of removing the VLAN from VPC, Configure VLAN 30,40 on both Nexus 3000-A-1 and A-2 as VPC VLANs.And, each Nexus switch has an orphan port conn...

kay.kang · 09-12-2023

Do I have to create manually user account on the switch? How can the NX-OS RBAC work with existing control access server(ACS in our case)?

kay.kang · 08-14-2023

We've got a public subnet to be advertised to the new ISP and we've got a routing design(using community and LP value) for inbound traffic from the ISP side to our side. Here, I am focusing on only outbound routing solution(regarding default route). ...

kay.kang · 08-14-2023

We've got a public subnet to be advertised to the new ISP and we've got a routing design(using community and LP value) for inbound traffic from the ISP side to our side. Here, I am focusing on only outbound routing solution(regarding default route). ...

Member Since	‎12-29-2021 09:31 PM
Date Last Visited	‎08-07-2024 01:09 AM
Posts	73
Total Helpful Votes Received	51

User Statistics

User Activity

Question about MSTP bridge priority

Question about setting up different VLAN between Nexus VPC peer

Select default route from RIP over EBGP

How to control command on Nexus switch with ACS based on priv level

How to set shell profiles and command sets to allow show run on ACS

Re: Question about setting up different VLAN between Nexus VPC peer

Re: Question about setting up different VLAN between Nexus VPC peer

Re: How to control command on Nexus switch with ACS based on priv leve

Re: Looking for best solution to migration new Internet link with BGP

Re: Looking for best solution to migration new Internet link with BGP