About jjevans1

jjevans1 · 10-26-2025

Hello All,Would like to know if there is a way to configure HA between 2 Cisco 1010 FTD using Device Manager? I was trying but the HA Configure button is greyed out due to error stating I need all interfaces to have a static IP address. I am looking ...

jjevans1 · 07-09-2025

I cannot deploy due to Cisco Client file that is on the FTD. It was fine before and I could deploy no problem. Now that Snort has an update I need to deploy but cannot due to error:The disk is (or was) full during extraction.WARNING: Unable to instal...

jjevans1 · 10-29-2024

I see FMC now supports the updates of FXOS and Firmware of the 4000 series. Has anyone used this feature successfully? Also does this support graceful failover? Or is this still done safer manually?

jjevans1 · 04-25-2024

Hello All,I have a 9500 that does not allow EIGRP. How do I enable it on the 9500 series switch?C9500(config-if)#ip router ?isis IS-IS Routing for IPVersion: Version 17.8.1rThank you for your insight.J

jjevans1 · 03-22-2024

Hello All,I have three routers in a lab with BGP peering.Router 1 - Location ARouter 2 – ISPRouter 3 – Location BI cannot seem to get the tunnel interface to come up because I cannot ping the other side.I can ping all interfaces but the tunnel inter...

jjevans1 · 10-27-2025

Because its a cable modem on that port that requires DHCP. Both guidelines do not state all interfaces require static IP. Just the HA ports. So is there a way to setup HA just on one port each? Maybe via CLI?

jjevans1 · 10-27-2025

Yes correct I need two static IP addresses for HA. But the error message and the HA button in Device Manager is greyed out saying I need all 8 interfaces to be static IP addresses. That is what I do not understand. And Yes port 1 is outside interface...

jjevans1 · 10-27-2025

Thank you that is helpful. My question then is why do all 8 interfaces need a static IP address? I just want to use one port from each firewall to dedicate to HA. I need port 1 to remain DHCP.

jjevans1 · 07-09-2025

Cleaned out upgrade directory then rebooted system. Ran all updates then was able to finally clear deployment.

jjevans1 · 07-09-2025

Disk space looks ok so not sure why deployment would fail? > show diskFilesystem Size Used Avail Use% Mounted onrootfs 3.3G 6.4M 3.3G 1% /devtmpfs 3.3G 5.5M 3.3G 1% /devtmpfs 3.9G 508K 3.9G 1% /run/dev/sda1 7.2G 1.6G 5.3G 23% /mnt/boot/dev/sda2 922M ...

Member Since	‎01-06-2022 11:45 AM
Date Last Visited	‎10-26-2025 12:36 PM
Posts	37
Total Helpful Votes Received	12

User Statistics

User Activity

HA without setting all interfaces with static IP addresses?

Cannot deploy due to disk0:/anyconnpkgs/cisco-secure-client-win-5.1.8.

FXOS and Firmware updates via FMC on 4000 series

Enable EIGRP on Cisco 9500 switch?

Cannot get Tunnel Interface to route

Re: HA without setting all interfaces with static IP addresses?

Re: HA without setting all interfaces with static IP addresses?

Re: HA without setting all interfaces with static IP addresses?

Re: Cannot deploy due to disk0:/anyconnpkgs/cisco-secure-client-win-5.

Re: Cannot deploy due to disk0:/anyconnpkgs/cisco-secure-client-win-5.