Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About talha_78_2000
Stats
Member since
06-28-2008
12
Posts
0
Helpful
0
Solutions
Created by
talha_78_2000
in IP Telephony and Phones
in IP Telephony and Phones
01-07-2014
02:45 AM
01-07-2014
02:45 AM
Thanks , The issue is fixed by changing the device pool of CIPC -SCCP to same as SIP trunk Device pool. But the CIPC - SIP is working fine with different device pool then the SIP trunk.
... View more
Created by
talha_78_2000
in IP Telephony and Phones
in IP Telephony and Phones
01-07-2014
01:05 AM
01-07-2014
01:05 AM
sureshsub2 wrote: It seems something wrong with the codec selection. we need to crosscheck the codec selection between CUCM & GW and also the preferred codec between the GW and ITSP. could you please capture the debug ccsip message & debug voice ccapi inout for SCCP CIPC call and SCCP IP phone call along with the GW running config? Hi , The debug output for 7911 phone and CIPC -SCCP and sh run for voice gateway is attached. I also test by checking "media termination point required" option on CUCM SIP trunk . By checking this option i am getting the ring then it desconnects.
... View more
Created by
talha_78_2000
in IP Telephony and Phones
in IP Telephony and Phones
01-06-2014
11:18 PM
01-06-2014
11:18 PM
Hi , Thanks for the help. I try both options "Check" and "Uncheck" "Optimize for low bandwidth" but it did not work . Can you explain me this Destn SIP Req Addr:Port : 10.43.1.1: 0 --> with CIPC SSCP . Where as Destn SIP Req Addr:Port : 10.43.1.1: 5060 --> with CIPC SIP Why the "Destn SIP Req Addr:Port" is 0 and how to fix it .
... View more
Created by
talha_78_2000
in IP Telephony and Phones
in IP Telephony and Phones
01-06-2014
05:45 AM
01-06-2014
05:45 AM
Hi I have the following setup CUCM ----Sip Trunk ----Voice GW Router ----Sip Trunk ---- PSTN( SIP Provider) All the Cisco ip phones with SIP and SCCP can dial outside through SIP GW and even cisco ip communicator - ( SIP ) can dial outside only Cisco IP communicator ( SCCP ) cannot dial outside. here the the debug output for both CIPC(SIP) and CIPC (SCCP): _______________________________________________________________ CIPC- SCCP --- Not Working 29A_0213_C1F0_VG2# Jan 6 10:49:43.076: //778580/3EBC03000000/SIP/Call/sipSPICallInfo: The Call Setup Information is: Call Control Block (CCB) : 0x0x26581380 State of The Call : STATE_DEAD TCP Sockets Used : YES Calling Number : 5627001 Called Number : 90559523514 Source IP Address (Sig ): 10.48.50.6 Destn SIP Req Addr:Port : 10.43.1.1:0 Destn SIP Resp Addr:Port : 10.43.1.1:40250 Destination Name : 10.43.1.1 Jan 6 10:49:43.076: //778580/3EBC03000000/SIP/Call/sipSPIMediaCallInfo: Number of Media Streams: 1 Media Stream : 1 Negotiated Codec : g711ulaw Negotiated Codec Bytes : 0 Nego. Codec payload : 18 (tx), 18 (rx) Negotiated Dtmf-relay : 6 Dtmf-relay Payload : 101 (tx), 101 (rx) Source IP Address (Media): 10.48.50.6 Source IP Port (Media): 0 Destn IP Address (Media): 10.17.1.35 Destn IP Port (Media): 24600 Orig Destn IP Address:Port (Media): [ - ]:0 Jan 6 10:49:43.076: //778580/3EBC03000000/SIP/Call/sipSPICallInfo: Disconnect Cause (CC) : 65 Disconnect Cause (SIP) : 488 _______________________________________________________________________ CIPS- SIP Jan 6 10:55:13.131: //778597/FD7823000000/SIP/Call/sipSPICallInfo: The Call Setup Information is: Call Control Block (CCB) : 0x0x26581380 State of The Call : STATE_DEAD TCP Sockets Used : YES Calling Number : 5627001 Called Number : 90559523514 Source IP Address (Sig ): 10.48.50.6 Destn SIP Req Addr:Port : 10.43.1.1:5060 Destn SIP Resp Addr:Port : 10.43.1.1:40250 Destination Name : 10.43.1.1 Jan 6 10:55:13.131: //778597/FD7823000000/SIP/Call/sipSPIMediaCallInfo: Number of Media Streams: 1 Media Stream : 1 Negotiated Codec : g729r8 Negotiated Codec Bytes : 20 Nego. Codec payload : 18 (tx), 18 (rx) Negotiated Dtmf-relay : 6 Dtmf-relay Payload : 101 (tx), 101 (rx) Source IP Address (Media): 10.48.50.6 Source IP Port (Media): 23964 Destn IP Address (Media): 10.17.1.35 Destn IP Port (Media): 17798 Orig Destn IP Address:Port (Media): [ - ]:0 Jan 6 10:55:13.131: //778597/FD7823000000/SIP/Call/sipSPICallInfo: Disconnect Cause (CC) : 16 Disconnect Cause (SIP) : 487 Jan 6 10:55:13.171: //778598/FD7823000000/SIP/Call/sipSPICallInfo: The Call Setup Information is: Call Control Block (CCB) : 0x0x265876F0 State of The Call : STATE_DEAD TCP Sockets Used : NO Calling Number : 5627001 Called Number : 0559523514 Source IP Address (Sig ): 172.29.33.106 Destn SIP Req Addr:Port : 10.200.7.157:5060 Destn SIP Resp Addr:Port : 10.200.7.157:5060 Destination Name : 10.200.7.157 Jan 6 10:55:13.171: //778598/FD7823000000/SIP/Call/sipSPIMediaCallInfo: Number of Media Streams: 1 Media Stream : 1 Negotiated Codec : g729r8 Negotiated Codec Bytes : 20 Nego. Codec payload : 18 (tx), 18 (rx) Negotiated Dtmf-relay : 6 Dtmf-relay Payload : 101 (tx), 101 (rx) Source IP Address (Media): 172.29.33.106 Source IP Port (Media): 23966 Destn IP Address (Media): 10.200.7.157 Destn IP Port (Media): 24756 Orig Destn IP Address:Port (Media): [ - ]:0 Jan 6 10:55:13.171: //778598/FD7823000000/SIP/Call/sipSPICallInfo: Disconnect Cause (CC) : 16 Disconnect Cause (SIP) : 487 _____________________________________________________________________________ debug ccsip message output 29A_0213_C1F0_VG2# Jan 6 12:39:01.388: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg: Received: INVITE sip:90559523514@10.48.50.6:5060 SIP/2.0 Via: SIP/2.0/TCP 10.43.1.1:5060;branch=z9hG4bK2664462864a1b4 From: <sip:5627001@10.43.1.1>;tag=27680380~502a4fce-c28e-4d6e-88a4-69e68a56e4e4-21547208 To: <sip:90559523514@10.48.50.6> Date: Mon, 06 Jan 2014 12:39:01 GMT Call-ID: 839b6600-2ca1a3e5-1f0efa-1012b0a@10.43.1.1 Supported: timer,resource-priority,replaces Min-SE: 1800 User-Agent: Cisco-CUCM8.6 Allow: INVITE, OPTIONS, INFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY CSeq: 101 INVITE Expires: 180 Allow-Events: presence Supported: X-cisco-srtp-fallback Supported: Geolocation Cisco-Guid: 2207999488-0000065536-0000000653-0016853770 Session-Expires: 1800 P-Asserted-Identity: <sip:5627001@10.43.1.1> Remote-Party-ID: <sip:5627001@10.43.1.1>;party=calling;screen=yes;privacy=off Contact: <sip:5627001@10.43.1.1:5060;transport=tcp> Max-Forwards: 70 Content-Type: application/sdp Content-Length: 234 v=0 o=CiscoSystemsCCM-SIP 27680380 1 IN IP4 10.43.1.1 s=SIP Call c=IN IP4 10.17.1.35 b=TIAS:8000 b=AS:8 t=0 0 m=audio 24578 RTP/AVP 18 101 a=rtpmap:18 G729/8000 a=ptime:20 a=rtpmap:101 telephone-event/8000 a=fmtp:101 0-15 Jan 6 12:39:01.390: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg: Sent: SIP/2.0 488 Not Acceptable Media Via: SIP/2.0/TCP 10.43.1.1:5060;branch=z9hG4bK2664462864a1b4 From: <sip:5627001@10.43.1.1>;tag=27680380~502a4fce-c28e-4d6e-88a4-69e68a56e4e4-21547208 To: <sip:90559523514@10.48.50.6>;tag=9E5DE660-2297 Date: Mon, 06 Jan 2014 12:39:01 GMT Call-ID: 839b6600-2ca1a3e5-1f0efa-1012b0a@10.43.1.1 CSeq: 101 INVITE Allow-Events: telephone-event Reason: Q.850;cause=65 Server: Cisco-SIPGateway/IOS-15.3.2.T Content-Length: 0 Jan 6 12:39:01.390: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg: Received: ACK sip:90559523514@10.48.50.6:5060 SIP/2.0 Via: SIP/2.0/TCP 10.43.1.1:5060;branch=z9hG4bK2664462864a1b4 From: <sip:5627001@10.43.1.1>;tag=27680380~502a4fce-c28e-4d6e-88a4-69e68a56e4e4-21547208 To: <sip:90559523514@10.48.50.6>;tag=9E5DE660-2297 Date: Mon, 06 Jan 2014 12:39:01 GMT Call-ID: 839b6600-2ca1a3e5-1f0efa-1012b0a@10.43.1.1 Max-Forwards: 70 CSeq: 101 ACK Allow-Events: presence Content-Length: 0 Jan 6 12:39:04.061: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg: Received: OPTIONS sip:172.29.33.106:5060 SIP/2.0 Via: SIP/2.0/UDP 10.200.7.157:5060;branch=z9hG4bKkseku4debfsbdsc7t7sbssefeT25609 Call-ID: isbcocfu4ocsd4oth7aukcfttch4hooubu7u@SoftX3000 From: <sip:172.29.33.106:5060>;tag=sbc0805abdkecos To: <sip:172.29.33.106> CSeq: 1 OPTIONS Max-Forwards: 70 Content-Length: 0 Jan 6 12:39:04.061: //778919/5C3CBD0087E9/SIP/Msg/ccsipDisplayMsg: Sent: SIP/2.0 200 OK Via: SIP/2.0/UDP 10.200.7.157:5060;branch=z9hG4bKkseku4debfsbdsc7t7sbssefeT25609 From: <sip:172.29.33.106:5060>;tag=sbc0805abdkecos To: <sip:172.29.33.106>;tag=9E5DF0CE-1207 Date: Mon, 06 Jan 2014 12:39:04 GMT Call-ID: isbcocfu4ocsd4oth7aukcfttch4hooubu7u@SoftX3000 Server: Cisco-SIPGateway/IOS-15.3.2.T CSeq: 1 OPTIONS Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER Allow-Events: telephone-event Accept: application/sdp Supported: timer,resource-priority,replaces,sdp-anat Content-Type: application/sdp Content-Length: 375 v=0 o=CiscoSystemsSIP-GW-UserAgent 2228 2785 IN IP4 172.29.33.106 s=SIP Call c=IN IP4 172.29.33.106 t=0 0 m=audio 0 RTP/AVP 18 0 8 9 4 2 15 c=IN IP4 172.29.33.106 m=image 0 udptl t38 c=IN IP4 172.29.33.106 a=T38FaxVersion:0 a=T38MaxBitRate:9600 a=T38FaxRateManagement:transferredTCF a=T38FaxMaxBuffer:200 a=T38FaxMaxDatagram:320 a=T38FaxUdpEC:t38UDPRedundancy Jan 6 12:39:24.110: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg: Received: OPTIONS sip:172.29.33.106:5060 SIP/2.0 Via: SIP/2.0/UDP 10.200.7.157:5060;branch=z9hG4bKoakbppkfut4btp4pd72p7thktT36254 Call-ID: isbc2t4dkcb2addb2p74ochsdkosohhkabka@SoftX3000 From: <sip:172.29.33.106:5060>;tag=sbc0803puccopdu To: <sip:172.29.33.106> CSeq: 1 OPTIONS Max-Forwards: 70 Content-Length: 0 Jan 6 12:39:24.110: //778920/683013A187EA/SIP/Msg/ccsipDisplayMsg: Sent: SIP/2.0 200 OK Via: SIP/2.0/UDP 10.200.7.157:5060;branch=z9hG4bKoakbppkfut4btp4pd72p7thktT36254 From: <sip:172.29.33.106:5060>;tag=sbc0803puccopdu To: <sip:172.29.33.106>;tag=9E5E3F1A-8D2 Date: Mon, 06 Jan 2014 12:39:24 GMT Call-ID: isbc2t4dkcb2addb2p74ochsdkosohhkabka@SoftX3000 Server: Cisco-SIPGateway/IOS-15.3.2.T CSeq: 1 OPTIONS Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER Allow-Events: telephone-event Accept: application/sdp Supported: timer,resource-priority,replaces,sdp-anat Content-Type: application/sdp Content-Length: 375 v=0 o=CiscoSystemsSIP-GW-UserAgent 4570 9684 IN IP4 172.29.33.106 s=SIP Call c=IN IP4 172.29.33.106 t=0 0 m=audio 0 RTP/AVP 18 0 8 9 4 2 15 c=IN IP4 172.29.33.106 m=image 0 udptl t38 c=IN IP4 172.29.33.106 a=T38FaxVersion:0 a=T38MaxBitRate:9600 a=T38FaxRateManagement:transferredTCF a=T38FaxMaxBuffer:200 a=T38FaxMaxDatagram:320 a=T38FaxUdpEC:t38UDPRedundancy 29A_0213_C1F0_VG2# Jan 6 12:39:44.166: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg: Received: OPTIONS sip:172.29.33.106:5060 SIP/2.0 Via: SIP/2.0/UDP 10.200.7.157:5060;branch=z9hG4bKcoohdcokbhchtebup7uebchppT05058 Call-ID: isbcuetdedhkobtoc2t2sfhcuohohh2ht24c@SoftX3000 From: <sip:172.29.33.106:5060>;tag=sbc0806duacdaa7 To: <sip:172.29.33.106> CSeq: 1 OPTIONS Max-Forwards: 70 Content-Length: 0 Jan 6 12:39:44.166: //778921/7424547D87EB/SIP/Msg/ccsipDisplayMsg: Sent: SIP/2.0 200 OK Via: SIP/2.0/UDP 10.200.7.157:5060;branch=z9hG4bKcoohdcokbhchtebup7uebchppT05058 From: <sip:172.29.33.106:5060>;tag=sbc0806duacdaa7 To: <sip:172.29.33.106>;tag=9E5E8D6C-234A Date: Mon, 06 Jan 2014 12:39:44 GMT Call-ID: isbcuetdedhkobtoc2t2sfhcuohohh2ht24c@SoftX3000 Server: Cisco-SIPGateway/IOS-15.3.2.T CSeq: 1 OPTIONS Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER Allow-Events: telephone-event Accept: application/sdp Supported: timer,resource-priority,replaces,sdp-anat Content-Type: application/sdp Content-Length: 375 v=0 o=CiscoSystemsSIP-GW-UserAgent 9077 3497 IN IP4 172.29.33.106 s=SIP Call c=IN IP4 172.29.33.106 t=0 0 m=audio 0 RTP/AVP 18 0 8 9 4 2 15 c=IN IP4 172.29.33.106 m=image 0 udptl t38 c=IN IP4 172.29.33.106 a=T38FaxVersion:0 a=T38MaxBitRate:9600 a=T38FaxRateManagement:transferredTCF a=T38FaxMaxBuffer:200 a=T38FaxMaxDatagram:320 a=T38FaxUdpEC:t38UDPRedundancy Jan 6 12:40:04.210: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg: Received: OPTIONS sip:172.29.33.106:5060 SIP/2.0 Via: SIP/2.0/UDP 10.200.7.157:5060;branch=z9hG4bKobhhh2aoob4t2akb4ahpee2h2T36723 Call-ID: isbcb7dbfff7ekekf2hpc74bd2o2fb4sbfo2@SoftX3000 From: <sip:172.29.33.106:5060>;tag=sbc0803opd7dahd To: <sip:172.29.33.106> CSeq: 1 OPTIONS Max-Forwards: 70 Content-Length: 0 Jan 6 12:40:04.210: //778922/8016C0E287EC/SIP/Msg/ccsipDisplayMsg: Sent: SIP/2.0 200 OK Via: SIP/2.0/UDP 10.200.7.157:5060;branch=z9hG4bKobhhh2aoob4t2akb4ahpee2h2T36723 From: <sip:172.29.33.106:5060>;tag=sbc0803opd7dahd To: <sip:172.29.33.106>;tag=9E5EDBB2-2114 Date: Mon, 06 Jan 2014 12:40:04 GMT Call-ID: isbcb7dbfff7ekekf2hpc74bd2o2fb4sbfo2@SoftX3000 Server: Cisco-SIPGateway/IOS-15.3.2.T CSeq: 1 OPTIONS Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER Allow-Events: telephone-event Accept: application/sdp Supported: timer,resource-priority,replaces,sdp-anat Content-Type: application/sdp Content-Length: 375 v=0 o=CiscoSystemsSIP-GW-UserAgent 1967 2233 IN IP4 172.29.33.106 s=SIP Call c=IN IP4 172.29.33.106 t=0 0 m=audio 0 RTP/AVP 18 0 8 9 4 2 15 c=IN IP4 172.29.33.106 m=image 0 udptl t38 c=IN IP4 172.29.33.106 a=T38FaxVersion:0 a=T38MaxBitRate:9600 a=T38FaxRateManagement:transferredTCF a=T38FaxMaxBuffer:200 a=T38FaxMaxDatagram:320 a=T38FaxUdpEC:t38UDPRedundancy
... View more
Labels:
Created by
talha_78_2000
in IP Telephony and Phones
in IP Telephony and Phones
08-03-2010
02:05 AM
08-03-2010
02:05 AM
We have three Cisco 7936 Conference station. These phones are working fine just 2 days back all three 7936 stop working, on all 7936 RED led is blinking and blank LCD display. Even after restarting it is giving the same problem right after powering on. I am sure it is some hardware problem. I want to know if some one face these problem before and whether the problem is with power adapter or phone and why all 7936 get problem at same time ? I don't have any spare power adapter or 7936 apart from these 3 pair to test and know the exact reason of problem, and these three phones with three adapter not working with any combination.
... View more
Labels:
12-14-2009
10:16 PM
Hi, I want to know if the module WS-X6148-GE-45AF is supported for VSS or not. If yes which IOS version i needed. The module is working fine with out VSS but when VSS is configured the module is not getting power form switch. Sh module output is given below for switch with VSS and Without VSS. I need ur help urgently.. Thanks. _________________________________________________________________________________________________________________ WITHOUT VSS CONFIGURED ............................... #sh module Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 1 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1309L4SN 2 6 Firewall Module WS-SVC-FWM-1 SAD13050148 3 48 48 port 10/100/1000mb EtherModule WS-X6148-GE-45AF SAL1309KW32 5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL124056Z6 Mod MAC addresses Hw Fw Sw Status --- ---------------------------------- ------ ------------ ------------ ------- 1 0024.97da.10bc to 0024.97da.10d3 3.3 12.2(18r)S1 12.2(33)SXI3 Ok 2 0021.a082.7b08 to 0021.a082.7b0f 4.5 7.2(1) 4.0(8) Ok 3 0024.c472.6638 to 0024.c472.6667 8.2 7.2(1) 12.2(33)SXI3 Ok 5 0019.e8bb.77cc to 0019.e8bb.77d3 3.0 8.5(3) 12.2(33)SXI3 Ok Mod Sub-Module Model Serial Hw Status ---- --------------------------- ------------------ ----------- ------- ------- 1 Centralized Forwarding Card WS-F6700-CFC SAL1308K4J4 4.1 Ok 3 IEEE Voice Daughter Card WS-F6K-48-AF SAL1309KUKS 2.3 Ok 5 Policy Feature Card 3 VS-F6K-PFC3C SAL1309KLLZ 1.0 Ok 5 MSFC3 Daughterboard VS-F6K-MSFC3 SAL1308K2LC 1.1 Ok Mod Online Diag Status ---- ------------------- 1 Pass 2 Pass 3 Pass 5 Pass ________________________________________________________________________________________________________________ WITH VSS CONFIGURED............. #sh module switch 1 Switch Number: 1 Role: Virtual Switch Active ---------------------- ----------------------------- Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 1 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1309L4SN 2 6 Firewall Module WS-SVC-FWM-1 SAD13050148 3 48 48 port 10/100/1000mb EtherModule WS-X6148-GE-45AF SAL1309KW32 5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL124056Z6 Mod MAC addresses Hw Fw Sw Status --- ---------------------------------- ------ ------------ ------------ ------- 1 0024.97da.10bc to 0024.97da.10d3 3.3 12.2(18r)S1 12.2(33)SXI3 Ok 2 0021.a082.7b08 to 0021.a082.7b0f 4.5 7.2(1) 4.0(8) Ok 3 0024.c472.6638 to 0024.c472.6667 8.2 Unknown 12.2(33)SXI3 PwrDown 5 0019.e8bb.77cc to 0019.e8bb.77d3 3.0 8.5(3) 12.2(33)SXI3 Ok Mod Sub-Module Model Serial Hw Status ---- --------------------------- ------------------ ----------- ------- ------- 1 Centralized Forwarding Card WS-F6700-CFC SAL1308K4J4 4.1 Ok 3 IEEE Voice Daughter Card WS-F6K-48-AF SAL1309KUKS 2.3 PwrDown 5 Policy Feature Card 3 VS-F6K-PFC3C SAL1309KLLZ 1.0 Ok 5 MSFC3 Daughterboard VS-F6K-MSFC3 SAL1308K2LC 1.1 Ok Mod Online Diag Status ---- ------------------- 1 Pass 2 Pass 3 Not Applicable 5 Pass
... View more
Labels:
06-30-2008
10:03 PM
Hello, I upgrade the IOS but it did not fix the problem. Still we have random one-way calls. After upgrade one of my E1 is not working and showing the status as BLOCKED. We have two E1 with 15 DID and 15 DOD each. I give the preference to other E1 so the calls are going through other E1. Please check the attachment and suggest me how to fix this problem. Thanks,
... View more
06-28-2008
09:40 PM
Yes i have access to 12.4(11)XJ4 , i can upgrade the IOS. Here is the output of sh controllers E1 E1 0/0/1 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20060711, FPGA: 13, spm_count = 0 Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line. CRC Threshold is 320. Reported from firmware is 320. Data in current interval (149 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Total Data (last 24 hours) 0 Line Code Violations, 0 Path Code Violations, 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins, 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
... View more
06-28-2008
05:57 AM
Yep i restarted the router many times but it did not fix the problem. The think which confusing me is the behavior of the problem its not fixed its random . we also check with the PSTN - E1 provider but they said there is not problem from there side and they have'nt make any changes on there side. I am suspecting the problem with the E1 module. but i dont have any other E1 module to test.
... View more
06-28-2008
05:28 AM
Our ip telephony setup was working fine from 1 year . Recently from one month it start giving problems. The External outgoing calls through E1 are sometimes one way - voice calls. We can here the voice but the other cannot here the voice. We did not change any configuration on the gateway. we are using 2811 (C2800NM-IPVOICE-M), Version 12.4(9)T1 of IOS on voice gateway. 1. We also have 4 FXO for international dialing. if we move the local calls to FXO there is no problem. 2. Incoming calls on E1 have no problem. 3. on outgoing calls there is problem but the problem is random. sometimes the call is two-way sometime its one-way call . we suspect that some channels may be one way so we monitor the calls but one the same channel of E1 some time the call is one way sometimes its two-way. controller E1 0/0/1 framing NO-CRC4 ds0-group 0 timeslots 1-15 type r2-digital r2-compelled ani ds0-group 1 timeslots 17-31 type r2-digital r2-compelled ani cas-custom 0 country saudiarabia use-defaults cas-custom 1 country saudiarabia use-defaults can anyone suggest or help regarding this issue. Thanks
... View more
Labels:
Created by
talha_78_2000
in IP Telephony and Phones
01-07-2014
01-07-2014
Thanks , The issue is fixed by changing the device pool of CIPC -SCCP to
same as SIP trunk Device po...
Created by
talha_78_2000
in IP Telephony and Phones
01-07-2014
01-07-2014
sureshsub2 wrote:It seems something wrong with the codec selection. we
need to crosscheck the codec ...
Created by
talha_78_2000
in IP Telephony and Phones
01-06-2014
01-06-2014
Hi , Thanks for the help. I try both options "Check" and "Uncheck"
"Optimize for low bandwidth" but ...
Created by
talha_78_2000
in IP Telephony and Phones
01-06-2014
01-06-2014
Hi I have the following setup CUCM ----Sip Trunk ----Voice GW Router
----Sip Trunk ---- PSTN( SIP Pr...
08-03-2010
We have three Cisco 7936 Conference station. These phones are working
fine just 2 days back all thre...
12-14-2009
Hi, I want to know if the module WS-X6148-GE-45AF is supported for VSS
or not. If yes which IOS vers...
Created by
talha_78_2000
in Unified Communications Infrastructure
08-24-2008
08-24-2008
No, we do not have Unity express. It is a small setup with about 15-20
ip phones and 8 - FXO lines a...
08-24-2008
I am very new to b-acd and scripts.Now we have call manager express
installed all incomming calls ar...
06-30-2008
Hello,I upgrade the IOS but it did not fix the problem. Still we have
random one-way calls. After up...
06-28-2008
Yes i have access to 12.4(11)XJ4 , i can upgrade the IOS.Here is the
output of sh controllers E1E1 0...
06-28-2008
Yep i restarted the router many times but it did not fix the problem.
The think which confusing me i...
Public Statistics
| Date Registered | 06-28-2008 05:11 AM |
| Date Last Visited | 12-02-2018 03:39 AM |
| Total Messages Posted | 12 |
