Simple guy from Romania passionate about networks and web design. You can see my personal web page for further information's, http://www.lazarmihail.net.
Since my version on the AP is ap801-k9w7-tar.124-21a.JY suppose the problem to be solved but look's like the problem is the same. Anyhow ... remain only to sell the router to somebody else to send the problems to another person, maybe he will figure it out the solution.
... View more
The problem is that I can not see the bug because " Your Cisco Guest Login is not entitled to use Bug Toolkit. Registered Customers and Partners may register for access here " Remains just to look on my cisco router and talk alone
... View more
Well no, but the wap had a new version and it was worse. Please tell me which version you are suggesting maybe I can get it. The thing that is making me nuts is that in the log of the wap in not leaving any error message. Cheers, Mihail
... View more
Hello, I know that the discussion is quite old but I didn't want to open another thread. The problem is that my AP is reloading randomly, in the beginning I was thinking that I'm doing huge transfers from my computer to the server attached to the router but even if the AP is not used is rebooting time to time. This problem is really frustrating and I don't know what to do anymore. Now the version on the AP is ap801-k9w7-mx.124-21a.JY as per above recommendations. Please let me know how to fix the problem because the router ( 861W ) is not in the warranty anymore and I can not open TAC requests to cisco. Thank you, Mihail
... View more
Hello, Sorry for this delay but I wasn't home this days. I attached the output of the log maybe somebody can tell me why the interface resets on high traffic after a few seconds. Thank you !
... View more
Hello again, Unfortunately is doing the same thing, the interface restarts when the traffic get really high. There is any way to limit the bandwidth on the wireless interface , QoS or something ? Thank you. Regards, Mihail
... View more
Hello, I have a problem with my router 861w and I don't know from where is this problem. The situation is like this: I have attached a hard drive on one of the Ethernet port of the router and I'm accessing this hard drive thru my laptop which is wireless connected. The problem is that when I start to transfer larger files from the hard drive to my laptop and the speed gets more or less 4 Mb / s the wireless card reset's and never go up after that. I have to reset the router by unplug it from the power source and then to transfer again. Please give me an advice how to solve this problem. I attached the configuration of the access point maybe is something wrong there. Regards, Mihail
... View more
Hello, I have a question for you guys. I set up my cisco 861w in order to get access to Internet at home. Everything was good except that I can't tune it in order to work on wireless N. Can you take a look at my attached configuration in order to make my network to function at wireless N speed. Thank you in advance. Lazar Mihail
... View more
Hello, Please read bellow the answer that I receive this night from apple : " if you're going to use a Cisco IPSec VPN with a Mac, you should use VPNTtacker, IPSecuritas or Shimo (preferred in that order) rather than the built in Mac VPN client. You need to match the configuration on the router precisely in order for this to work. I would also suggest contacting Cisco support directly I'd you continue to have problems. I would also strongly advise against using a Time Capsule for anything business related. I recommend the Promise NS4600, but there are many alternatives. That said, one way you could easily reach the Time Capsule from a Mac virtually anywhere is by using Apple 's Back To my Mac feature, part of it's Mobile Me service. Hope this helps. " I will try tomorrow if one of the vpn clients software that they are advice are working or not. Regards,
... View more
Well ... I discuss also with Apple support people but they told me that is not the MacBook fault and I should look in the settings of our router but I'm wondering if there is any whay to test the VPN connection using another client besides the Cisco VPN client which is soming with MacBook.
... View more
Hello, 1) Verify you are connecting to the same group as the windows machines * Yes, there is only one group created for VPN connections. 2) Verify that you are getting an IP address in the same range as the windows machines - receiving same networks/routes via split tunneling(if you are split tunnelign) * Yes, I'm receiving an IP address from 192.168.10.0 / 24 network witch is the same as windows machines. Also I configure it for split tunneling and I'm receiving 192.168.2.1 autommaticaly as DNS server. 3) Can you ping the router interface address on the 192.168.2 network? * From windows machines yes, I can ping 192.168.2.0 / 24 network but from MacBook I can't, only 192.168.1.0 / 24 network. 4) Does your mac have any firewall installed on it? Is the lan IP address in overlapping with the 192.168.2/24 address space? * On MacBook I don't have the firewall activated and is not overlaping with 192.168.2.0 network because I'm connecting thru a 3G network and the provider gives me a public address. Please see attached configuration of the router and ap and give me an advice or a hint where to look in order to fix the problem because this MacBook start to give me head headings. Thank You. Mihail
... View more