About goncalo_gil

goncalo_gil · 03-01-2011

Hi Team,I am running ASR1002 with latest XE IOS version asr1000rp1-adventerprisek9.03.02.01.S.151-1.S1.binconfiguration bellowrouter bgp 65000 bgp router-id 1.1.1.1 bgp log-neighbor-changes timers bgp 5 15 ! address-family ipv4 vrf LABR01-VRF bgp ro...

goncalo_gil · 01-24-2011

Hi Guys,I have VRF Lite using "shared" VRF interfaces and leaking unicast routes via RT (route targets imports/exports + BGP).I wanted to do similar import/export with multicast tables.Is anyone aware if this is possible or routing table leaking is o...

goncalo_gil · 01-24-2011

Hi Guys,Have anyone tried to tunnel BDF peers traffic through a l2protocol or Q-in-Q tunnel?I can see UDLD is possible but wanted to go step further an tunnel BFD traffic (from non-directly attached BFD peers).ThanksGonz

goncalo_gil · 11-27-2009

Hi Forum,I have a 6506-E unit with dual Sup2/MSFC2 running Native IOS 122-18.SXF8 on SSO mode. Every one in a while the units freeze for a very short period (seconds) but leaves no record on the logs/cli outouts.We have decreased the timers for the s...

goncalo_gil · 08-26-2009

Hi Forum,I am testing L2 port security when attaching Corporate swith to an external switch.1. I can disable STP on the port so the external switch does not affect my network. 2. Add BPDU Guard to it in case it starts STP. 3. change VTP default domai...

goncalo_gil · 01-27-2011

Hello,You can also use PBR to split traffic type per circuit if wanted. You may get asymetric routing on some of the traffic. It is difficult to say wiouth knowing the full setup.I hope it helps.Gonçalo

goncalo_gil · 01-27-2011

Hello,If you already configured syslgo on this units you can add the command bellow on the interface config menuinterface GigabitEthernetx/x logging event link-statusGood luckGonçalo

goncalo_gil · 01-27-2011

Hello,There is no formal documentation for this procedure (as far I am aware). I learned this technique a while back.There is a document highlighting most common issues for high CPU utilization on 6500. This can give you a pretty good idea:http://www...

goncalo_gil · 01-26-2011

Hello,You can probably see the module if you use the commandshow inventory rawI hope it helpsRegardsGonçalo

goncalo_gil · 01-26-2011

Hello,It sounds like your MSFC is getting hit with high level of traffic at maybe for very short periods and dificult to trace if this are microburst.You can SPAN the MSFC to a sniffer port as bellow and apply ACL to filter unwanted traffic. This way...

Member Since	‎11-23-2006 02:32 PM
Date Last Visited	‎08-18-2017 03:54 AM
Posts	37

User Statistics

User Activity

ASR1002 unable to use BGP route-map match next-hop on inbound

VRF Lite multicast route leaking

Can you tunnel BFD traffic on a l2protocol or Q-in-Q tunnel?

6500 Sup2/MSFC2 Freeze for no reason

6500 IOS Native L2 Port Security (VTP/STP/CDP/others)

Re: BGP Internet trafic

Re: How to get line protocol up/down notification at SP level?

Re: 6509 Sup2 - weird CPU usage and packet loss

Re: Cisco 2951 can't see SM-D-ES3-48-P module.

Re: 6509 Sup2 - weird CPU usage and packet loss