01-26-2011 02:39 AM - edited 03-04-2019 11:12 AM
Hello and thanks to anyone who will answer this post. I have the situation with my new Cisco 2951 router. It has only one module on board - SM-D-ES3-48-P. I don't know what is wrong but I can't see any information about this module. When I connect my laptop to any port it's become green, but it's still green even after I disconnect PC from this port. Sh ip int brief command shows only built-in gigabit interfaces. I also connect my second PC to the router by console to monitor any changes when I connect or disconnect laptop to the module's ports. No messages was generated.
there is Sh hardware command output:
Internet#sh hardware
Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.0(1)M3, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Sun 18-Jul-10 03:51 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M6, RELEASE SOFTWARE (fc1)
Internet uptime is 19 minutes
System returned to ROM by reload at 10:10:02 UTC Wed Jan 26 2011
System image file is "flash0:c2951-universalk9-mz.SPA.150-1.M3.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
Cisco CISCO2951/K9 (revision 1.1) with 481280K/43008K bytes of memory.
Processor board ID FHK1445F17G
4 Gigabit Ethernet interfaces
1 terminal line
DRAM configuration is 72 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
254464K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
-------------------------------------------------
Device# PID SN
-------------------------------------------------
*0 CISCO2951/K9 FHK1445F17G
Technology Package License Information for Module:'c2951'
----------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
-----------------------------------------------------------------
ipbase ipbasek9 Permanent ipbasek9
security None None None
uc None None None
data None None None
Configuration register is 0x2102
Solved! Go to Solution.
01-26-2011 05:05 AM
Hi,
service-module gigabit
For example, if the module is in slot 2, use the below command,
service-module gigabit 2/0 session
Regards,
Nagendra
01-26-2011 07:51 AM
Hello,
You can probably see the module if you use the command
show inventory raw
I hope it helps
Regards
Gonçalo
01-26-2011 05:05 AM
Hi,
service-module gigabit
For example, if the module is in slot 2, use the below command,
service-module gigabit 2/0 session
Regards,
Nagendra
01-26-2011 07:51 AM
Hello,
You can probably see the module if you use the command
show inventory raw
I hope it helps
Regards
Gonçalo
01-26-2011 06:52 PM
Thank you very much, guys. Now I can configure those interfaces.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide