Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About titozep99
Stats
Member since
01-03-2013
6
Posts
0
Helpful
0
Solutions
09-04-2013
04:40 PM
The cable I am using is 3ft (0.9mt) long and all 4 pairs are in good condition.
... View more
09-04-2013
03:13 PM
I upgraded the code and now: 1) I have an additional message: 00:15:34: %ILPOWER-7-DETECT: Interface Gi0/1: Power Device detected: Cisco PD 00:15:51: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 2) sh power inline does not report a faulty connection: SW_ALMACEN#sh power inli Available:370.0(w) Used:15.4(w) Remaining:354.6(w) Interface Admin Oper Power Device Class Max (Watts) --------- ------ ---------- ------- ------------------- ----- ---- Gi0/1 auto on 15.4 Cisco PD n/a 15.4 Gi0/2 auto off 0.0 n/a n/a 15.4 Gi0/3 auto off 0.0 n/a n/a 15.4 Gi0/4 auto off 0.0 n/a n/a 15.4 3) Cable diagnostics shows: Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi0/1 auto Pair A 152 +/- 4 meters N/A Normal Pair B 152 +/- 4 meters N/A Normal Pair C 1 +/- 4 meters N/A Short Pair D 1 +/- 4 meters N/A Short I will RMA the device Thank you...
... View more
09-03-2013
04:31 PM
#sh log Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) Console logging: level debugging, 156 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 156 messages logged, xml disabled, filtering disabled Exception Logging: size (4096 bytes) Count and timestamp logging messages: disabled File logging: disabled Trap logging: level informational, 159 message lines logged Log Buffer (4096 bytes): er port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:42:06: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:42:21: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:42:36: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:42:51: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:43:06: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:43:21: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:43:37: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:43:53: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:44:08: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:44:24: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:44:41: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:44:56: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:45:11: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:45:26: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:45:42: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:45:57: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:46:14: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:46:29: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:46:44: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:47:00: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power given, but Power Controller does not report Power Good 00:47:15: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, In 00:49:21: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Pow ...continues No, Leo. Anythig else seems to work well. #sh power inl Available:370.0(w) Used:0.0(w) Remaining:370.0(w) Interface Admin Oper Power Device Class Max (Watts) --------- ------ ---------- ------- ------------------- ----- ---- Gi0/1 auto off 0.0 n/a n/a 15.4 Gi0/2 auto off 0.0 n/a n/a 15.4 Gi0/3 auto off 0.0 n/a n/a 15.4 Gi0/4
... View more
09-03-2013
03:59 PM
Here's the output: #sh post Stored system POST messages: Switch 1 --------- POST: CPU MIC register Tests : Begin POST: CPU MIC register Tests : End, Status Passed POST: PortASIC Memory Tests : Begin POST: PortASIC Memory Tests : End, Status Passed POST: CPU MIC interface Loopback Tests : Begin POST: CPU MIC interface Loopback Tests : End, Status Passed POST: PortASIC RingLoopback Tests : Begin POST: PortASIC RingLoopback Tests : End, Status Passed POST: PortASIC CAM Subsystem Tests : Begin POST: PortASIC CAM Subsystem Tests : End, Status Passed POST: PortASIC Port Loopback Tests : Begin POST: PortASIC Port Loopback Tests : End, Status Passed # I enabled the port. Error appeared again.
... View more
09-03-2013
12:38 PM
Our 3560G-24 switch suddenly lost POE ports (with IP phones connected to them) at the same time. In the log there is this error: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/x: Power given, but Power Controller does not report Power Good I isolated the switch, disconnect everything and reconnect just one device for testing. I have tried some things recommended with no luck (shut down and up, change cable, IP Phone, etc, no power inline auto, etc.). Here some command outputs: #sh ver Cisco IOS Software, C3560 Software (C3560-IPBASE-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Thu 19-Jul-07 18:15 by nachen #sh pow inl Available: 370.0(w) Used:0.0(w) Remaining:370.0(w) Interface Admin Oper Power Device Class Max (Watts) --------- ------ ---------- ------- ------------------- ----- ---- Gi0/1 auto faulty 0.0 n/a n/a 15.4 Gi0/2 auto off 0.0 n/a n/a 15.4 Gi0/3 auto off 0.0 n/a n/a 15.4 Gi0/4 auto off 0.0 n/a n/a 15.4 Gi0/5 auto off 0.0 n/a n/a 15.4 Gi0/6 auto off 0.0 n/a n/a 15.4 Gi0/7 auto off 0.0 n/a n/a 15.4 Gi0/8 auto off 0.0 n/a n/a 15.4 Gi0/9 auto off 0.0 n/a n/a 15.4 Gi0/10 auto off 0.0 n/a n/a 15.4 Gi0/11 auto off 0.0 n/a n/a 15.4 Gi0/12 auto off 0.0 n/a n/a 15.4 Gi0/13 auto off 0.0 n/a n/a 15.4 Gi0/14 auto off 0.0 n/a n/a 15.4 Gi0/15 auto off 0.0 n/a n/a 15.4 Gi0/16 auto off 0.0 n/a n/a 15.4 Gi0/17 auto off 0.0 n/a n/a 15.4 Gi0/18 auto off 0.0 n/a n/a 15.4 Gi0/19 auto off 0.0 n/a n/a 15.4 Gi0/20 auto off 0.0 n/a n/a 15.4 Gi0/21 auto off 0.0 n/a n/a 15.4 Gi0/22 auto off 0.0 n/a n/a 15.4 Gi0/23 auto off 0.0 n/a n/a 15.4 Gi0/24 auto off 0.0 n/a n/a 15.4 # test cable tdr int gi0/1 #sh cable-diagnostics tdr int gi0/1 Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi0/1 auto Pair A 152 +/- 4 meters N/A Normal Pair B 149 +/- 4 meters N/A Normal Pair C 1 +/- 4 meters N/A Short Pair D 1 +/- 4 meters N/A Short I know Pair C controls PoE and pair D GigabitEthernet. If I connect a non-poe device all appears "Normal" I think the internal PS is faulty. Is there any additional tests or command to fix or to confirm this? Thank you for your help.
... View more
Labels:
01-03-2013
02:51 PM
I have remote offices connected to my data center with wireless links (ubiquiti radios in wds transparent mode and Tycon switches at solar powered sites). Remote offices can only be reached with a wireless link of several hops... I am installing VOIP telephony at the remote sites using Cisco´s SPA504G IP phones. But the phone does not register to my Asterisk server located at the data center. When I check it with wireshark I see the phone does not receive the ARP reply it is waiting for (no DHCP, my Asterisk server is at 172.31.0.10 and the default gateway is 172.31.0.1): Then I disconnect the SPA504G and connect a Polycom IP 301 phone (everything else remains untouched) and with this model the ARP request/reply is completed and the phone registers: The problem lies in the wireless link and the Cisco phone confiiguration. Any clues will be appreciated. Thank you in advance
... View more
Labels:
09-04-2013
I upgraded the code and now:1) I have an additional message:00:15:34:
%ILPOWER-7-DETECT: Interface G...
09-03-2013
#sh logSyslog logging: enabled (0 messages dropped, 1 messages
rate-limited, 0 flushes, 0 overruns, ...
09-03-2013
Here's the output:#sh postStored system POST messages: Switch 1---------
POST: CPU MIC register Test...
09-03-2013
Our 3560G-24 switch suddenly lost POE ports (with IP phones connected to
them) at the same time. In ...
Public Statistics
| Date Registered | 01-03-2013 02:16 PM |
| Date Last Visited | 08-18-2017 03:55 AM |
| Total Messages Posted | 6 |
