About slilley92

slilley92 · 02-08-2008

Hello,I come from a frame-relay background, and we are going to be evaluating metro ethernet. We have a test site setup, and I am able to get it to come up when connecting 1841 routers on each end with no vlans. However, when I try to connect to our ...

slilley92 · 02-08-2008

Hello,I come from a frame-relay background, and we are going to be evaluating metro ethernet. We have a test site setup, and I am able to get it to come up when connecting 1841 routers on each end with no vlans. However, when I try to connect to our ...

slilley92 · 09-25-2007

We have a WS-6148-GE-TX and are looking to buy a spare, but the one our supplier has is a WS-6148V-GE-TX. Can we just remove the PoE daughtercard? Will that mess anything up? I have never seen one of these PoE modules so I am hoping it is just a matt...

slilley92 · 05-21-2007

I have a 2811 which currently has a NM-4A/S running in it. I want to remove that and put in a NM-2W with a WIC-1DSU-T1-V2. Is that module slot hot swappable?

slilley92 · 06-15-2006

I need to configure QoS, and think what I am trying to do is very simple, but am starting to see cross-eyed when reading all of Cisco's documentation on ways to implement QoS. Could someone please point me in the right direction? Here is the story: W...

slilley92 · 09-25-2007

Jorge, thank you very much! That helps a lot. I think we will just remove the daughtercard, then, since we won't be connecting any phones, just data connections. Steve

slilley92 · 05-21-2007

I just found the answer to my question, so thought I would post it here in case others in the future have the same question. I found the answer here: http://www.cisco.com/en/US/products/ps5854/products_qanda_item0900aecd80169bd6.shtmlHere is the answ...

slilley92 · 06-16-2006

Hi Vlad,Actually, they are NEC phone switches. The phones themselves are regular digital units, it is the actual switches themselves which communicate via TCP/IP. That is what makes me think it shouldn't be all that hard. What I have tried is setting...

slilley92 · 06-16-2006

What is the history of this router? Did you recently make changes, like a new IOS, for example? That software forced reload error makes me wonder if you do not have enough DRAM to run the IOS currently loaded in it. I know you said you tried differen...

slilley92 · 07-24-2003

Roger! That is exactly it! I just figured this out before I read your response. We have 2 PVCs on the frame circuit to the router in question; I had ip nat inside defined on the primary but not the secondary. Once I added 'ip nat inside' to the secon...

Member Since	‎07-09-2003 07:01 AM
Date Last Visited	‎08-18-2017 03:50 AM
Posts	15
Total Helpful Votes Received	5

User Statistics

User Activity

Need configuration help setting up metro ethernet please

Need help with MetroE configuration on 6509 with CatOS please!

What is the difference between WS-6148-GE-TX and WS-6148V-GE-TX?

Is module slot on 2811 hot swappable?

Need simple QoS configuration

Re: What is the difference between WS-6148-GE-TX and WS-6148V-GE

Re: Is module slot on 2811 hot swappable?

Re: Need simple QoS configuration

Re: NEED URGENT HELP WITH MY CISCO 2600 ROUTER

Re: NAT works on some devices on same network, but not others