Good Afternoon Lime Soft, After review your question I need to let you know that this type of configuration is not recommendable. To Use both connections in order to connect the same end devices, would cause a loop. Beside that, According to the information provided, you are trying to connect the Lan with 2 WAP54g's separate by a distance of  500 meters (152Ft) and the maximum rate of these devices is 75Ft. So I would recommend you decide between both connections and if you go for the LAN connection, to use a device with more range or get the devices closer. Thank you. ... View more

Hello Mr. Hessenauer, On this case I recommend you to install the latest firmware available for this device (2.0.1.3) Let me send you the link from the cisco site where you could download it. http://www.cisco.com/cisco/software/release.html?mdfid=282414016&softwareid=282487380&release=2.0.1.3&relind=available&rellifecycle=&reltype=latest If this answer was satisfactory for you, please mark the question as Answered. Diego Rodriguez Cisco network engineer Thank you ... View more

Hello Mr. Sagastum, My name is Diego and I am part of the Small  business Support community. I have seen your  post and would like to help you with information  that might be helpful on your case. On the next link you would find an example of VPN tunnel configuration, step by step. You could find this and more information about our cisco small business products on the guide me section. http://sbkb.cisco.com/CiscoSB/ukp.aspx?vw=1&docid=b88c949b4d35460fac902f16ee08e44c_Configuration_of_Backup_Tunnel_on_RV016__RV042__and_RV082.xml&pid=4&fcid=&fpid=&slnid=4 If this answer was satisfactory for you, please mark the question as Answered. Diego Rodriguez Cisco network engineer Thank you ... View more

Hello Mr. Mccullough, Thank you for your question. However, you have posted it on the wrong forum, please post it on small business Security forum, in order to get a better response. You can move your post using the Actions panel on the right. Best regards, Diego Rodriguez Cisco Small Business Community Engineer Best regards, ... View more

Hello Mr. Brown, Thank you for your question. However, the Small Business Support Community is limited to Cisco Small Business Products and the WRT54GS router is an Enterprise level product. You might consider to ask this question at Enterprise forum to get a better response. https://supportforums.cisco.com/index.jspa Best regards, Diego Rodriguez Cisco Small Business Community Engineer ... View more

Hello Mr. Gniecko , My name is Diego and I am part of the Small  business Support community. I have seen your  post and would like to help you with information  that might be helpful on your case. You could find this and more information about our Cisco small business products on the guide me section. http://is6.nohold.net/CiscoSB/ukp.aspx?vw=1&docid=e87a6038f33d45629be4836efd3fe177_WDS_repeater_mode_set_up_on_a_WAR4400_series_router.xml&pid=4&fcid=&fpid=&slnid=11 If this answer was satisfactory for you, please mark the question as Answered. Diego Rodriguez Cisco network engineer Thank you ... View more

Hello Mr. Mason, Welcome to the Small business support comunity. Let me share with you some information related to the NAT configuration on a RV042, found on the guide me setion where you could find all the information related with Cisco Small businness products configuration. http://is6.nohold.net/CiscoSB/ukp.aspx?vw=1&docid=e3105749e13f40a3a302802259189e07_Setting_Port_Range_Forwarding_for_the_RV042.xml&pid=4&fcid=&fpid=&slnid=18 http://is6.nohold.net/CiscoSB/ukp.aspx?vw=1&docid=2134697b1d7844cfa16a300fb0762cd2_Setting_Port_Triggering_for_the_RV082.xml&pid=4&fcid=&fpid=&slnid=18 hope you find this answer useful, if it was satisfactory  for you, please mark the question as Answered. Diego Rodriguez Cisco network engineer Thank you ... View more

Hello Mr. McDonald, Let me share with you a list of SIP, that as far as I know are located on Ireland. At this moment, as I am not located on Ireland, so I can not give you a personal recommendation which one to choose, but I hope that you could find one that fits your expectations. SupplyIP Ireland EagleVision VoIP Solutions Procom Telephone Systems IPTELECOM Speechpath.ie Infinity IT Cinditel communication Emutex Welltel Zen Telecom VEECOMMS RocTel International Voiptechnologies Webangel International Network Systems ltd G7eleven MyDivert.com ABizNews hope you find this answer useful, if it was satisfactory   for you, please mark the question as Answered. Thank you ... View more

Hello Mr. Stian Bjerk Thank you for joining the Cisco small business Community, In order to provide the best support possible you will find assistance for all Cisco Small business products. In this case DynDNS is not a tool provided by Cisco. To point you in the right direction please contact the software developer of this product. Thank you and I hope you find this answer useful.   ... View more

Olá Sr. Ribeiro, De acordo com as informações encontradas a lista de clientes sem fio é visível dentro da via GUI: Wireless -> Controle de Conexão -> local, em seguida, clique em Lista de clientes sem fio. Deixe-me enviar o link com o manual do WAP4410N onde eu encontrei. Por favor, consulte a página 46. http://www.cisco.com/en/US/docs/wireless/access_point/csbap/wap4410n/administration/guide/WAP4410N_Admin_Guide.pdf Espero que esta resposta seja útil, se ele foi satisfatória para você, por favor, marque a pergunta como respondida. obrigado ... View more

Hello Mr. O'Sullivan Let me share with you some information that I found about Monitoring Wireless Cisco devices. Is needed to access the Wireless Control system. Once you are there please follow the next instructions. Step 1 Click Monitor > Clients to navigate to the Clients Summary page. Step 2 The sidebar area enables you to select a new configuration panel under the menu area that you have selected. You can make only one choice. The selector area options vary based on the menu that you select. • New Search drop-down menu: Opens the Search Clients window. Use the Search Clients window to configure, run, and save searches. • Saved Searches drop-down menu: Lists the saved custom searches. To open a saved search, choose it from the Saved Searches list. • Edit link : Opens the Edit Saved Searches window. You can delete saved searches in the Edit Saved Searches window. Step 3 In the sidebar, click New Search . The Search Clients window appears. You can configure the following parameters in the Search clients window: • Search By • Clients Detected By — Choose WCS for clients stored in WCS that were detected through polling of the controllers from WCS. Choose Location Servers for clients stored on the location server that were detected by the location server through controller polling. • Last detected within — A time increment from 5 minutes to 24 hours. • Client States —Specify if you want to view clients only in a specific state such as idle, authenticated, associated, probing, or excluded. • Include Disassociated — To include clients that are no longer on the network but for which WCS has historical records. • Restrict By Protocol — To restrict the search by protocol. Then from the drop-down menu choose 802.11a, 802.11b, and 802.11g. • Restrict by SSID — To restrict the search by SSID. Then enter the SSID in the text field. • CCX Compatible — To search for CCX compatible clients. • E2E Compatible — To search for E2E compatible clients. • Save Search — To save the search in the Saved Searches drop-down menu. • Items per page — The number of found items to display on the search results page. Step 4 Choose All Clients in the Search By drop-down menu and click GO. The related search results window appears. The search results are listed. Let me send you the link from the Cisco site where I found this information. http://www.cisco.com/en/US/docs/wireless/wcs/4.1/configuration/guide/wcsmon.html#wp1090194 hope you find this answer useful, if it was satisfactory for you, please mark the question as Answered. Thank you Select VLAN Select the ID of the VLAN whose port membership you are configuring. For each port in the VLAN, select the appropriate configuration option: Tagged The interface is a member of the VLAN. All packets transmitted by the port will be tagged and will carry VLAN information. Untagged The interface is a member of the VLAN. All packets transmitted by the port will be untagged and will not carry VLAN information. Excluded The interface is excluded from the VLAN. You could check this information on the VLAN to Port screen which displays each port’s VLAN membership information. It is also used to add a port to or delete a port from a VLAN. hope you find this answer useful, if it was satisfactory for you, please mark the question as Answered. Thank you Hello Mr. O'Sullivan Let me share with you some information that I found about Monitoring Wireless Cisco devices. Is needed to access the Wireless Control system. Once you are there please follow the next instructions. Step 1 Click Monitor > Clients to navigate to the Clients Summary page. Step 2 The sidebar area enables you to select a new configuration panel under the menu area that you have selected. You can make only one choice. The selector area options vary based on the menu that you select. • New Search drop-down menu: Opens the Search Clients window. Use the Search Clients window to configure, run, and save searches. • Saved Searches drop-down menu: Lists the saved custom searches. To open a saved search, choose it from the Saved Searches list. • Edit link : Opens the Edit Saved Searches window. You can delete saved searches in the Edit Saved Searches window. Step 3 In the sidebar, click New Search . The Search Clients window appears. Hello Mr. O'Sullivan Let me share with you some information that I found about Monitoring Wireless Cisco devices. Is needed to access the Wireless Control system. Once you are there please follow the next instructions. Step 1 Click Monitor > Clients to navigate to the Clients Summary page. Step 2 The sidebar area enables you to select a new configuration panel under the menu area that you have selected. You can make only one choice. The selector area options vary based on the menu that you select. • New Search drop-down menu: Opens the Search Clients window. Use the Search Clients window to configure, run, and save searches. • Saved Searches drop-down menu: Lists the saved custom searches. To open a saved search, choose it from the Saved Searches list. • Edit link : Opens the Edit Saved Searches window. You can delete saved searches in the Edit Saved Searches window. Step 3 In the sidebar, click New Search . The Search Clients window appears. Hello Mr. O'Sullivan Let me share with you some information that I found about Monitoring Wireless Cisco devices. Is needed to access the Wireless Control system. Once you are there please follow the next instructions. Step 1 Click Monitor > Clients to navigate to the Clients Summary page. Step 2 The sidebar area enables you to select a new configuration panel under the menu area that you have selected. You can make only one choice. The selector area options vary based on the menu that you select. • New Search drop-down menu: Opens the Search Clients window. Use the Search Clients window to configure, run, and save searches. • Saved Searches drop-down menu: Lists the saved custom searches. To open a saved search, choose it from the Saved Searches list. • Edit link : Opens the Edit Saved Searches window. You can delete saved searches in the Edit Saved Searches window. Step 3 In the sidebar, click New Search . The Search Clients window appears. ... View more

Hello Mr. McCoy, Let me share with you some information about the configuration of vlans and port assignation for this kind of interface and switch. In order to create a vlan you need to access the Create VLAN screen. The Vlan management interface lets you create and configure global parameters for VLANs. To create a single VLAN, enter the VLAN ID and VLAN Name, up to 32 characters long, and click Add. After create the vlan you could go to the The Port Settings where you to configure the ports in a VLAN. You can configure VLAN behavior for specific ports, including the accepted frame type, VLAN identifier (PVID), and ingress filtering. Port The number of the port. Acceptable Frame Type This specifies the type of frames that the port will accept. If All (default) is selected, the port will accept all frame types, including tagged or untagged frames. If Tagged is selected, the port accepts only tagged frames. When set to All, any untagged frames that are received are assigned to the default VLAN. PVID Use this field to select the VLAN ID that will be assigned to untagged frames received on the port. Valid IDs are (default) to 409. VLAN 4094 is reserved for internal use. VLAN 4095 is defined per standard and industry practice as the Discard VLAN. Frames tagged for the Discard VLAN are dropped. Ingress Filtering Enables or disables Ingress filtering on the port. Ingress filtering discards packets that do not include an ingress port. The default is Enabled. LAG Displays the LAG, if any, to which the port belongs. A port’s LAG settings override the VLAN port settings. Click Save Changes to save your changes, or click Cancel Changes to cancel. Next Go to the the Port to VLAN screen. In this screen you could to add ports to a VLAN and delete ports from a VLAN. When you add a port to a VLAN, you also specify whether the port is tagged or untagged. The Port to VLAN screen contains a Port Table with VLAN parameters for each port. To add a port to or delete a port from the VLAN, you select the port’s appropriate configuration options from this table Select VLAN Select the ID of the VLAN whose port membership you are configuring. For each port in the VLAN, select the appropriate configuration option: Tagged The interface is a member of the VLAN. All packets transmitted by the port will be tagged and will carry VLAN information. Untagged The interface is a member of the VLAN. All packets transmitted by the port will be untagged and will not carry VLAN information. Excluded The interface is excluded from the VLAN. You could check this information on the VLAN to Port screen which displays each port’s VLAN membership information. It is also used to add a port to or delete a port from a VLAN. I hope you find this answer useful, if it was satisfactory for you, please mark the question as Answered. Thank you ... View more

Hello Mr. Costa, According the information found the lenght of this value is predefined, it can not be set to more than 30 digits. hope you find this answer useful, if it was satisfactory  for you, please mark the question as Answered. Thank you ... View more

Hello Mr. Cotter, The last firmware available for a WAP4410N  is the version 2.0.5.3. Let me send you the link fro the Cisco site where you could download it. http://www.cisco.com/cisco/software/release.html?mdfid=282414137&release=2.0.3.3&relind=AVAILABLE&softwareid=282463166&rellifecycle=&reltype=all hope you find this answer useful, if it was satisfactory  for you, please mark the question as Answered. Thank you ... View more