Dear all,   I have a switch Cisco SG500X-48 (image version : 1.3.0.62) and this switch is actually in system mode L3.    I would like to switch it on L2 mode, but in the web GUI, in "Administration" > "System Mode and Stack Management", two radio buttons L2 and L3 are disabled. I can't change.   I also tried via the "menu" in CLI, but I do not know either change.   How to do ? Thanks for your help :-)   Best Regards, Fabien ... View more

Hello, I see that there is no mention "k9" (for crypto) in version of my router. By the wayn it's impossible to activate SSH ? :-( router#show version Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-UNIVERSAL-M), Version 15.1(1)S, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2010 by Cisco Systems, Inc. Compiled Mon 22-Nov-10 12:32 by mcpre Cisco IOS-XE software, Copyright (c) 2005-2010 by cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software. ROM: IOS-XE ROMMON uptime is 2 minutes Uptime for this control processor is 3 minutes System returned to ROM by reload System image file is "bootflash:/asr1001-universal.03.02.00.S.151-1.S.bin" Last reload reason: PowerOn Thanks for your help Fabien ... View more

Hello, I have a router Cisco ASR1001 with 4 GigabitEthernet SPF port. Which is compatible ? I see "CISCO GLC-SX-MMD" (http://www.ldlc-pro.com/fiche/PB00170432.html )  but is expensive :) There are cheaper models? Thanks Best Regards, Fabien ... View more

Hello, I have a problem with Cisco ASR1001 MGMT port (GigabitEthernet0). The port is down and I do not know why. Interface configuration : interface GigabitEthernet0 vrf forwarding Mgmt-intf ip address 10.30.10.30 255.255.255.0 negotiation auto ! vrf definition Mgmt-intf ! address-family ipv4 exit-address-family ! address-family ipv6 exit-address-family ! Port status : GigabitEthernet0 is down, line protocol is down Hardware is RP management port, address is ccef.48ea.b7c0 (bia ccef.48ea.b7c0) Internet address is 10.30.10.30/24 MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Auto Duplex, Auto Speed, link type is auto, media type is RJ45 output flow-control is unsupported, input flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts (0 IP multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out I don't know why the port is down. The port is yet connected with a cable directly to a switch, but no connectivity. An idea ? Thanks :) Best Regards, Fabien ... View more