About criitdept

criitdept · 06-21-2012

Hi,I hope someone can help me with this.I have enabled Jumbo Frames in our iSCSI Network to hopefully help speed things up (I really wanted to use more of the available bandwidth as have gigabit nics which are only be utilised by 5-10%)This consists ...

criitdept · 06-12-2012

All,I wander if you can help with this.I currently have 4 3560 switches connected in a Mesh topology. These are all set to use Jumbo Frames and so are all the Servers that are connected to these.I now need to connect a 2950 switch to 2 of the 3560's ...

criitdept · 11-25-2010

Hi,I hope someone can help me with this question.My network is set up as the diagram.I now need to turn on Jumbo Frames on to VLAN 30 for a storage network.To do this, i need change the mtu to 9000 on Switches A+C+DBy doing this....will this cause an...

criitdept · 11-22-2010

HiI hope someone can help me with this.I have 3 Cisco Catalyst 3560 Switches connected as per the diagram.I have just configured these with MST in Region 1 and Instance 1When I have the etherchannel unplugged between A + B and I check spanning-tree s...

criitdept · 06-04-2008

Hi,I have created a VPN between a remote site and our headofficeThe remote site has a Cisco 877 Router and the HeadOffice has a Cisco 3005 Concentrator.The VPN i have created is up and running and I can connect to devices at either sides of the VPN.T...

criitdept · 06-22-2012

Hi Soroush,Thanks for the config.I have tried it but unfortunately, it doesn't seem to have helped.Do i need to then apply this to particular interfaces?ThanksJames

criitdept · 06-21-2012

Hi Soroush,Thanks for the quick response.As I'm pretty new to doing this, can you explain how to do this and a correct benchmarck for these.Thanks again,

criitdept · 06-12-2012

Thanks for the quick response.I didn't really want to go into the switch setup as it is actually 10 switches with a few VLANs.One of these VLANs is a Storage VLAN and is the reason I want to use Jumbo Frames, so that i can get the most out of my iSCS...

criitdept · 03-17-2008

The VPN is working.I have found a few articles and they have said that i need to setup a GRE VPN over ipsec to allow the dhcp broadcast, unfortunately this requires version 7 of the IOS on the PIX and as i only have a 501, this runs 6.3. so i'm now g...

criitdept · 11-30-2005

Thanks for the guide.I have set everything up as instructed in the guide but when i try to access anything on the second tunnel it trys to send everything to the peer on the first tunnelAny ideas why this would beCheersJames

Member Since	‎11-29-2005 04:15 AM
Date Last Visited	‎08-18-2017 03:56 AM
Posts	15

User Statistics

User Activity

Enabled Jumbo Frames but now I have High Total Outqueue Drops

Jumbo Frames and connecting non-jumbo Switches

Jumbo Frame Across Multiple Switches

MST and Etherchannel Question

Do i need to increase to MTU size?

Enabled Jumbo Frames but now I have High Total Outqueue Drops

Enabled Jumbo Frames but now I have High Total Outqueue Drops

Jumbo Frames and connecting non-jumbo Switches

Re: DHCP Relay Over IPSEC VPN between a PIX and VPN Concentrator

Re: Vpn between Pix 501 and 501 and vpn concentrator