Hi,   Can anybody tell me if this version has the fix applied 10.5.1.11901-1 - It isn't in the list of known fixed releases.   Regards, Dave ... View more

Hi Leonardo, I'm well aware of how to display actively logged in device report in CUCM i need to export that data, which isn't possible from CUCM. Do you know of a way of extracting it? Regards Dave ... View more

Abzal, How is your gateway configured, We had a site in Pontecchio and Motara which had problems making calls.H323  Isdn interface config below. Italia Telecom was the provider ! interface Serial0/0/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn overlap-receiving T302 5000 isdn incoming-voice voice isdn send-alerting isdn bchan-number-order ascending isdn sending-complete no cdp enable ! voice-port 0/0/0:15 translation-profile incoming INCOME-DDI echo-cancel coverage 32 no vad cptone IT bearer-cap Speech ! E1 0/0/0 is up.   Applique type is Channelized E1 - balanced   No alarms detected.   alarm-trigger is not set   Version info Firmware: 20071009, FPGA: 20, spm_count = 0   Framing is CRC4, Line Code is HDB3, Clock Source is Line.   CRC Threshold is 320. Reported from firmware  is 320.   Data in current interval (649 seconds elapsed):      0 Line Code Violations, 0 Path Code Violations      0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins      0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs   Total Data (last 24 hours)      1 Line Code Violations, 1 Path Code Violations,      0 Slip Secs, 0 Fr Loss Secs, 1 Line Err Secs, 0 Degraded Mins,      1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Cheers Dave ... View more

Abzal, How is your gateway configured, We had a site in Pontecchio and Motara which had problems making calls.H323  Isdn interface config below. Italia Telecom was the provider ! interface Serial0/0/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn overlap-receiving T302 5000 isdn incoming-voice voice isdn send-alerting isdn bchan-number-order ascending isdn sending-complete no cdp enable ! voice-port 0/0/0:15 translation-profile incoming INCOME-DDI echo-cancel coverage 32 no vad cptone IT bearer-cap Speech ! E1 0/0/0 is up.   Applique type is Channelized E1 - balanced   No alarms detected.   alarm-trigger is not set   Version info Firmware: 20071009, FPGA: 20, spm_count = 0   Framing is CRC4, Line Code is HDB3, Clock Source is Line.   CRC Threshold is 320. Reported from firmware  is 320.   Data in current interval (649 seconds elapsed):      0 Line Code Violations, 0 Path Code Violations      0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins      0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs   Total Data (last 24 hours)      1 Line Code Violations, 1 Path Code Violations,      0 Slip Secs, 0 Fr Loss Secs, 1 Line Err Secs, 0 Degraded Mins,      1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Cheers Dave ... View more

You might want to restart the Cisco ip voice media streaming APP on your tftp server and try again. ... View more

Is it ISDN30 ... View more

Have you tried translating your incoming number to a physical IP phone to see if ringback is generated ? ... View more

Does the incoming number translate to the same route point as the other numbers which have no issues ? ... View more

What does your script do with the call ? Does the call get answered straight away by IPCC then present the caller with options. I.E 1 for this 2 for that ? Once the caller makes a decision and presses 1 or 2 ringback is usually generated by the annunciator until the call is answered. Does the route point for this number use the same MRGL as the others. regards Dave ... View more

Hi Jake, Do all the inbound numbers translate to the same route point ? If not you may want to check the IPCC script has the correct configuration for that route point. Are you using E1/T1 Regards Dave ... View more

Cheers Paolo. Let me get this clear the second modem type has the standard rj connectivity ? ... View more

Hi Paolo, One more thing does the second modem give a presentaion of G703 and will i need a converter cable (Balon) or does it have rj45/48 connectivity. Regards Dave ... View more

Hi Paolo, Does it use standard rj45 or rj48 connectivity ? Is it configured the same way as a standard E1 Regards Dave ... View more