In the Cisco ONS SONET TL1 Reference Guide, it mentions the following. Issuing commands to specific nodes in the network is accomplished by entering a unique node name in the TID field in each TL1 message. The TID field is synonymous with the name of the node and is the second token in a TL1 command. Is there a TL1 command to first get a list of the nodes that it is a gateway for like RTRV-GW-NELIST that I have seen on other devices. Thanks, Greg ... View more

Is there a TL1 command that can be run to get the list of ports and possibly their current admin/operational status from a card on a Cisco 15454 SONET?  The RTRV-INV and RTRV-EQPT seems like they list only card level information.  Looking for a query that will list the interfaces/ports. Thanks, Greg ... View more

I know this is a big request, but was wondering if someone could capture the output of a few TL1 commands on an ONS15454 SONET for me?  Other 15454 models might be useful too.  I don't currently have access to any, but would like to see real output examples.  The command guides give examples, but you can tell they are fake if a part number is ABCDEF. RTRV-INV::ALL:a RTRV-EQPT::ALL:a RTRV-NE-GEN:::a RTRV-NETYPE:::a Just zip and attach. Extremely appreciative, Greg ... View more

  i'm having a strange problem with IOS-XR and removing class-map references from policy-maps.  It does not seem to let me remove a reference to a class-map and remove the class-map in the same transaction.  Is this a bug?  I sent the commands in the correct order but it looks like the commit is evaluating them out of order. Thanks, Greg RP/0/4/CPU0:rotgsr-2#configure Thu Oct 14 11:29:25.912 EDT RP/0/4/CPU0:rotgsr-2(config)#policy-map mqc-phb-2 RP/0/4/CPU0:rotgsr-2(config-pmap)#no  class my_cos RP/0/4/CPU0:rotgsr-2(config-pmap)#exit RP/0/4/CPU0:rotgsr-2(config)#no class-map match-any my_cos RP/0/4/CPU0:rotgsr-2(config)#commit confirmed % Failed to commit one or more configuration items during a pseudo-atomic operation. All changes made have been reverted. Please issue 'show configuration failed' from this session to view the errors RP/0/4/CPU0:rotgsr-2(config)#show configuration failed Thu Oct 14 11:30:13.546 EDT !! SEMANTIC ERRORS: This configuration was rejected by !! the system due to semantic errors. The individual !! errors with each failed configuration command can be !! found below. ! no class-map my_cos !!% Object is in use: Class-map "my_cos" of type "qos" is used by policy-map(s). Delete failed. end ... View more

  Trying to figure out the requirements for upgrading to PRP on a 12008.  What I am trying to figure out is if my current LCs will be supported by PRP.  Haven't found a page that talks about PRP compatible LC. Thanks, Greg rotgsr-1#show diags | include FRU|SLOT|Memory SLOT 0  (RP/LC 0 ): Route Processor   FRU:  Linecard/Module: GRP-B=         Route Memory: MEM-GRP/LC-256= SLOT 1  (RP/LC 1 ): 1 Port Gigabit Ethernet   FRU:  Linecard/Module: GE-GBIC-SC-B=         Processor Memory: MEM-GRP/LC-256=         Packet Memory: MEM-LC1-PKT-256=   Processor Memory size: 268435456 bytes   TX Packet Memory size: 134217728 bytes, Packet Memory pagesize: 8192 bytes   RX Packet Memory size: 134217728 bytes, Packet Memory pagesize: 8192 bytes SLOT 2  (RP/LC 2 ): 4 Port Packet Over SONET OC-3c/STM-1 Single Mode   FRU:  Linecard/Module: LC-4OC3/POS-SM=         Processor Memory: MEM-GRP/LC-256=         Packet Memory: MEM-LC-PKT-128=   Processor Memory size: 268435456 bytes   TX Packet Memory size: 67108864 bytes   RX Packet Memory size: 67108864 bytes SLOT 3  (RP/LC 3 ): 6 Port Packet over DS3   FRU:  Linecard/Module: 6DS3-SMB-B=         Processor Memory: MEM-GRP/LC-256=         Packet Memory: MEM-LC-PKT-128=   Processor Memory size: 268435456 bytes   TX Packet Memory size: 67108864 bytes   RX Packet Memory size: 67108864 bytes SLOT 5  (RP/LC 5 ): 4 port ATM Over SONET OC-3c/STM-1 Single Mode   FRU:  Linecard/Module: 4OC3/ATM-IR-SC=         Processor Memory: MEM-GRP/LC-128=         Packet Memory: MEM-LC-PKT-128=   Processor Memory size: 134217728 bytes   TX Packet Memory size: 67108864 bytes   RX Packet Memory size: 67108864 bytes SLOT 16 (CSC 0   ): Clock Scheduler Card(8)   FRU:  Linecard/Module: GSR8-CSC/ALRM= SLOT 17 (CSC 1   ): Clock Scheduler Card(8)   FRU:  Linecard/Module: GSR8-CSC/ALRM= SLOT 18 (SFC 0   ): Switch Fabric Card(8)   FRU:  Linecard/Module: GSR8-SFC= SLOT 19 (SFC 1   ): Switch Fabric Card(8)   FRU:  Linecard/Module: GSR8-SFC= SLOT 20 (SFC 2   ): Switch Fabric Card(8)   FRU:  Linecard/Module: GSR8-SFC= SLOT 24 (PS A1   ): DC Power Supply(8)   FRU:  Linecard/Module: PWR-GSR8-DC= ... View more

  So I'm new to the 12K series for linecard firmwares.  I've been tasked to upgrade all the ROMs and such in prep for migration from IOS to IOS-XR. The requirements are: Line cards (LCs) For Engine 3 line card: – Maintenance Bus (MBUS) Agent Software-RAM version 04.06, ROM version 04.06 – ROM Monitor version 17.1 – Fabric Downloader - RAM version 8.0, ROM version 8.0 (The ROM version will be the same as the RAM version if upgraded.) Route processors (RPs) For Performance Route Processor 2 (PRP-2): –Maintenance Bus (MBUS) Agent Software-RAM version 04.06, ROM version 04.06 – ROM Monitor version 1.24 I am currently at: rotgsr-2#show diags | include SLOT | ROM Monitor       SLOT 4  (RP/LC 4 ): Performance Route Processor   ROM Monitor version 1.24 SLOT 5  (RP/LC 5 ): 4 Port ISE Gigabit Ethernet   ROM Monitor version 19.1 rotgsr-2#show diags | inc SLOT| MBUS | Fabric Downloader SLOT 4  (RP/LC 4 ): Performance Route Processor   MBUS: MBUS Agent (1)  73-8048-07 rev A0 dev 0   MBUS Agent Software version 2.72 (RAM) (ROM version is 3.69) SLOT 5  (RP/LC 5 ): 4 Port ISE Gigabit Ethernet   MBUS Agent Software version 2.72 (RAM) (ROM version is 3.69)   Fabric Downloader version used n/a (ROM version is 7.9) rotgsr-2#dir Directory of disk0:/     1  -rw-     6892544   Oct 8 2010 13:38:58 -04:00  c12k-fpd-pkg.120-33.S7.pkg     2  -rw-    31299072   Oct 8 2010 13:44:50 -04:00  c12kprp-p-mz.120-33.S7.bin How do i find the correct IOS load to help upgrade to the correct firmwares?  Obviously, the latest 12.0S isn't enough.  And why does the Fabric Downloaded say version n/a?  Did I miss a step? Thanks, Greg ... View more

  I installed a new IOS load on my 2951 and but it failed to boot with the following error. IOS Image Load Test ___________________ Unsigned Image Found, bailing out Signature DID NOT VERIFY boot: cannot load "flash0:"   Is there something wrong with c2951-universalk9-mz.SPA.151-2.T1.bin?  Or is there additional steps with the 2951 that I haven't learned about yet.  This is my first 2900. Thanks, Greg ... View more

I am trying to figure out how to, if possible, for AAA to use Radius talking IPv6.  Is such a thing supported?  I can't get the 'radius-server' command to accept an IPv6 address as the host address.  I even tried setting a hostname that resolved to IPv6 address, but that didn't work either. Currently trying c7200-adventerprisek9-mz.122-33.SRE.bin. Thanks, Greg ... View more