Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Boris Knezovic
Stats
Member since
12-31-2009
13
Posts
20
Helpful
4
Solutions
01-23-2013
02:43 AM
Rodrigo, Trick to make Linksys PAP2T working with CUCME is to make device making and receiving calls without registration. Under Line settings you should set yes to Make Call Without Reg: and Ans Call Without Reg. Proxy address is address of your CUCME, you do not need OB Proxy and need to set dial plan at the bottom. We used this solution for connecting Fax devices to CUCME some time ago and it seems to be working without problems. Unfortunaltely I can not connect to those devices to help you with exact configuration. Regards. Boris
... View more
Created by
Boris Knezovic
in ATAs, Gateways and Accessories
in ATAs, Gateways and Accessories
08-17-2012
12:51 AM
08-17-2012
12:51 AM
Bjarne, I had a same problem with SPA112 and increasing SIP T1 timer from default value of 0.5 to 5 solved issue with dropped outgoing calls. Here is the link to original message: https://supportforums.cisco.com/message/3615397#3615397 Regards Boris
... View more
07-18-2012
01:44 AM
Paul, You are mixing Cisco Unified Communications Manager where Cisco Jabber for Android is supported with Cisco Unified Communications Manager Express which is running on UC500 series devices and where it is not. Not yet... Regards Boris
... View more
07-18-2012
12:43 AM
Paul, Cisco Jabber for Android is not yet supported on UC500 platform. Regards. Boris
... View more
Created by
Boris Knezovic
in ATAs, Gateways and Accessories
in ATAs, Gateways and Accessories
06-04-2012
04:26 AM
06-04-2012
04:26 AM
Petr, I tried setting network parameters on my test Cisco SPA112 device with firmware v1.1.0(011) using IVR, and I can confirm that it could not be done as device would not save the parameters. Hope that Cisco will solve this bug, and SIP T1 timer bug, with new version of firmware. Regards. Boris
... View more
Created by
Boris Knezovic
in ATAs, Gateways and Accessories
in ATAs, Gateways and Accessories
06-01-2012
05:24 AM
06-01-2012
05:24 AM
Petr, SPA112 IVR Manual is available here: http://www.cisco.com/en/US/docs/voice_ip_comm/csbpvga/spa100-200/quick_start/SPA100_ATA_78-19933.pdf I did not tried configuring network parameters using IVR on Cisco SPA112 but commands are same as Linksys PAP2T so IVR should behave the same way. Basically, you choose IVR command number and press #, enter value, press # and press 1 to save. Regards. Boris
... View more
Created by
Boris Knezovic
in Voice Systems
in Voice Systems
02-10-2012
12:32 AM
02-10-2012
12:32 AM
Steve, Your load command can't read file located in TFTP subfolder so either it should be in the root of the flash or you can use alias command as: tftp-server flash:/phones/50x-30x/spa50x-30x-7-4-9c.bin alias spa50x-30x-7-4-9c.bin Regards Boris
... View more
Created by
Boris Knezovic
in IP Telephony and Phones
in IP Telephony and Phones
09-06-2011
06:23 AM
09-06-2011
06:23 AM
Rob, This thread in UC500 section confirms that update to 8.2.0 should bring additional licenses: https://supportforums.cisco.com/message/3413007#3413007 They mention "show lic detail" and "show platform software lic" commands to check the license details on the unit. Unfortunately I only have UC520 available and did not tried license update myself. Regards Boris
... View more
Created by
Boris Knezovic
in IP Telephony and Phones
in IP Telephony and Phones
09-06-2011
12:25 AM
09-06-2011
12:25 AM
Gus, You will have 24 user licenses if you load 8.2.0 software pack. Check CCA 3.1 release notes: http://www.cisco.com/en/US/docs/net_mgmt/cisco_configuration_assistant/version3_1/release/Notes/cca_3_1_relnotes.html Regards Boris
... View more
09-02-2011
05:24 AM
Fabio, Phone1 and Phone2 LED's will light only when line is active (meaning your PAP2T is registered at VoIP server). Are you trying to use PAP2T with local SIP server or at IP Telephony Service Provider network? Could problem be that your PAP2T is residing inside your local network (NAT) and unable to reach IPTSP? What is Registration State of your Line1 at PAP2T initial (Info) screen Regards. Boris
... View more
08-31-2011
12:22 AM
Fabio, If box is a brand new then you need either to have DHCP in your network or to set static IP address on the box. Network parameters are set using embeded IVR as described in this document: http://www.nyct.net/PAP2T_ug.pdf Regards. Boris
... View more
Created by
Boris Knezovic
in ATAs, Gateways and Accessories
in ATAs, Gateways and Accessories
05-19-2011
01:10 AM
05-19-2011
01:10 AM
Dial Time Planer is what you need and you will find it on Page 67 of the above manual. Boris
... View more
01-23-2013
Rodrigo,Trick to make Linksys PAP2T working with CUCME is to make device
making and receiving calls ...
Created by
Boris Knezovic
in ATAs, Gateways and Accessories
08-17-2012
08-17-2012
Bjarne,I had a same problem with SPA112 and increasing SIP T1 timer from
default value of 0.5 to 5 s...
07-18-2012
Paul,You are mixing Cisco Unified Communications Manager where Cisco
Jabber for Android is supported...
Created by
Boris Knezovic
in ATAs, Gateways and Accessories
06-04-2012
06-04-2012
Petr,I tried setting network parameters on my test Cisco SPA112 device
with firmware v1.1.0(011) usi...
Created by
Boris Knezovic
in ATAs, Gateways and Accessories
06-01-2012
06-01-2012
Petr,SPA112 IVR Manual is available
here:http://www.cisco.com/en/US/docs/voice_ip_comm/csbpvga/spa10...
Created by
Boris Knezovic
in Voice Systems
02-10-2012
02-10-2012
Steve,Your load command can't read file located in TFTP subfolder so
either it should be in the root...
Created by
Boris Knezovic
in IP Telephony and Phones
09-06-2011
09-06-2011
Rob,This thread in UC500 section confirms that update to 8.2.0 should
bring additional
licenses:http...
Created by
Boris Knezovic
in IP Telephony and Phones
09-06-2011
09-06-2011
Gus,You will have 24 user licenses if you load 8.2.0 software pack.
Check CCA 3.1 release
notes:http...
09-02-2011
Fabio,Phone1 and Phone2 LED's will light only when line is active
(meaning your PAP2T is registered ...
08-31-2011
Fabio,If box is a brand new then you need either to have DHCP in your
network or to set static IP ad...
Public Statistics
| Date Registered | 12-31-2009 03:58 AM |
| Date Last Visited | 02-11-2019 05:16 AM |
| Total Messages Posted | 13 |
| Total Helpful Votes Received | 20 |
.jpg "Hall of Fame Community Legend"){kind=icon}
